Wireless Joint

Understood. You want to self build, support, and warrant. :) Pretty much what the cost of the InvisaGig is.

They have rj45 modem sleds on alibaba that you drop your own 5G modem into, or buy theirs, and use AT commands or opensource code to give it a web interface for sending at commands ...

Understood. You want to self build, support, and warrant. :) Pretty much what the cost of the InvisaGig is.

They have rj45 modem sleds on alibaba that you drop your own 5G modem into, or buy theirs, and use AT commands or opensource code to give it a web interface for sending at commands.

Yea ...

That's not to bad, but a bit more than I want to spend. Big worry is, will it work with the ATT Mobley plan, I really don't want to have to use something else, as it's been rock solid for years and years with me, and I usually use around 1TB a month. Is there just a modem version of this? I don ...

I'm a huge fan of this device: https://thewirelesshaven.com/shop/routers/cellular-internet-hotspot/with-wifi/dual-band-wifi/gigabit-ethernet/m2-modem-slot/nexpro-wifi6-router-rm520ngl/

I know it's a bit higher than you stated. But it's SUPER simple to operate. You can change imei by just typing a ...

False alarm, I just apparently was being impatient, usually it connects in under a minute, but connected in like 4 minutes this time.

I will say, I think it might be time for me to upgrade. I'm still on this card which is pushing like 8 years now, and still on the mobley plan, don't want to change ...

Usually an AT!Reset fixes it, but it seems to be stuck in a loop now. I've been using this for years at this point with no issue. Woke up this morning, internet was fine for about 5mins and then it stopped working. Did the reset and router reboot, which usually fixes it but this time it's in a full ...

Just started tonight, both modems doing same thing, with the same simcard (figured it might be a modem issue). This is a ATT mobley account. connected directly to the modem (either one) packets drop, connected to it via Wireguard, packets drop. Both modems are in 2 different routers WG series. My ...

I'm glad it's working for you, but most people are unable to set up a separate VPN box.
Hopefully in the future, mobile routers will have enough processing power to be able to run a VPN with minimal speed degradation.

They need to release wireguard option on the LEDE/ROOTer goldenorb firmware ...

Have you had any luck with trying to set it to IPV6? I can't get my modem to stick to that. That being said I haven't had a disconnect since last week (knock on wood and whatever else).

Unfortunately no, mine also wouldn't take at all. It'd just kill the internet and never connect with those ...

Update - MTU doesn't resolve this. TTL same thing.

i have been having the disconnects for months, I keep updating the new firmware, mine doesn't require a reboot, i actually lose all connection to the tower. at least that is how the Moxi is reporting it, however within a minute or 2 it reconnects ...

https://windscribe.com

At first I created my own Wireguard server at Digital Ocean but Windscribe works great so there's no point or saving in having my own since I paid for a year at Windscribe for $45. It has a config generator which gives you raw configuration rather than forcing you to use ...

A ping test won't work because pings are successful even when you can't get http or https to load. I can ping any domain when I lose connectivity but can't get to any websites (other than Google). Already opened sessions (eg zoom calls) continue to work as well. ATT is black-holing web (80/443 ...

I am on ATT, will try the IPV6 fix.

Let me know how it goes.

Would a VPN fix this?

I'm just tethering to a phone via Wireguard and EasyTether to Windscribe VPN. All I ever pass over cellular are UDP packets.

Edit: I see that someone already mentioned VPN. FWIW, Wireguard is working well ...

Updated: Wifix The Wireless Haven Ping Test, while I'm sure it works, isn't a solution, waiting 10mins before it checks ping is way to long. A version in which this is shortened to like 5-10 seconds could help, but the 10min mark, you're already going into the router page and rebooting it yourself.

The below is the solution to this issue with dd-wrt and wireguard.

New Update + Final Solution: So with KeepSolid, it's $99 for a lifetime, then I spend $12.50 a month for a private IP, everything works now, gaming/P2P/VOIP/etc. This is the recommended route I suggest you go with for any VPN ...

I've had my data connection timed out on my M1 after a few hours but using a VPN does solves the problem. I'm using ExpressVPN through a L2TP connection instead of OpenVPN. OpenVPN kills my data speeds by half when using on a router. L2TP maintains my original speeds. AT&T seems to be killing ...

Could someone please post again if these become fixed?
Don't want to try this service with these known issues at the moment.
Thanks

We will, I'd watch this thread as well.

https://forums.att.com/conversations/other-phones-devices/att-transparent-proxy-not-stable-hanging-connections-to-websites ...

What AT&T plan is everyone having this issue on? Want to know been considering trying AT&T "Unlimited For iPad" or "Unlimited for Tablet" plan myself.

The plan isn't the issue. It's effecting even people with just cell phone plans.

https://forums.att.com/conversations/other-phones-devices/att ...

corywf wrote: Fri Oct 23, 2020 9:44 am I tried those commands yesterday. After the reset it didn't reconnect. I did a power cycle and the settings didn't stick. It was back to ipv4v6 and connected giving me an IPV4 address.

Yeah looks like this isn't going to work with us with ATT.

It's not a DNS issue. It's ATT black-holing your traffic with their transparent proxy. There's a big thread here (it sounds like IPV6 bypasses the proxy but I can't figure out how to force IPv6 with my EM7565/already tried a few commands).

https://forums.att.com/conversations/other-phones-devices ...

Please don't take this as nitpicking, just would like to point out the correct expression of your down/up speeds.
If you put down 100+MBs, it means MegaBytes/sec (upper case B=Bytes, lover case b=bits), which would equal to 800Mbps (Megabits/sec), and I'm pretty sure you're getting nowhere near ...

Are you me!? This literally started happening like 4 days ago. (WG3526) Yes I'm on ATT, and I've changed my DNS settings and it still randomly happens. Anyone got an idea of what it might be?

Doing an AT!Reset get's everything running again. It's been fine for literally years, and now it's doing ...

So wanting to update this....basically 4G on ATT doesn't allow for port forwarding because they still use IPV4, so I'm NATed with like 100 other people on the same public IP. I got around this though as I have a VPN and just request a port and use it. Sucks but I'm on the Mobily plan paying $23 for ...

So I'm having a bit of an issue, I'm trying to forward a port and there are two spots for it in the Network -> FireWall Location. I'm seeing Port Forwards and then under Traffic Rules also a port forward. Which do I need to be using?

I've tried
Source Zone being Wan/wan1/wan2 (modem)
Source IP ...

xdavidx wrote: Wed Jul 24, 2019 1:38 pmCongrats!

I don't know if this is a good or bad thing though, makes me feel like my hands are %100 tied when dealing with this. As who can I call to tell them a tower is crap? Basically no one, I just have to wait almost 2 months for things to get better or hope they get better.

So, just to update this, after everything I did, I'm magically back to low ping, no VPN...I'm going to take a guess and say there was something horribly wrong with the tower I connect to, as I'm back to normal everything.

It seems like you have multiple issues.

1) Without VPN, something weird is going on with Verizon. It seems AT&T is okay. Maybe switching to AT&T is your easiest option.

Yeah, today I turned off the VPN, and now am getting normal connection, ping is still high but download isn't 20kbs anymore ...

Well, I understand that you have Verizon issues, but my suggestion is to reduce variables if you want to figure out the cause of the slower pings. Fast.com is a unique situation and that will tell you how Netflix will behave, but to determine if the VPN is adding to the latency, I'd recommend ...

@serverside: Try setting the "use small packets" setting in your PIA VPN client. I looked back over your posts and saw that you mentioned that is your VPN provider.

https://www.privateinternetaccess.com/helpdesk/kb/articles/my-ping-latency-is-really-high

I don't see how it could help the ping ...

Yes, they have to be otherwise my connection is like 10-50kbs on Fast.com and drops packets and lags, it's completely unusable. I'm on a verizon MVNO, but I've never had this issue before.

So just tried playing a game and my ping is just as bad as before, might be a little worse since it seems ...

xdavidx wrote: Wed Jun 26, 2019 6:19 pm Are all your latency tests through a VPN?

Yes, they have to be otherwise my connection is like 10-50kbs on Fast.com and drops packets and lags, it's completely unusable. I'm on a verizon MVNO, but I've never had this issue before.

I don't know exactly, but its been a few releases back.

I noticed that too randomly when trying a newer version of GoldenOrb.

So just tried it, and it does work on my build version. I'm connected and....it does give me lower latency, still going through a VPN, BUT it's where I used to be, 30 ...

serverside wrote: Tue Jun 25, 2019 8:19 am Cool, So now I need to know if my April build will handle QMI for my MC7455. Anyone know when the first build allowed for it to work?

Anyone know the answer to this? When did the Rooter builds start working with QMI?

IPv6 works fine with QMI on both Sprint and Verizon.

Tested on:
1) GO 3-10
2) OpenWRT w/MM
3) Arch w/MM
Verizon was on the EM7565 (FW12) for all 3. Sprint was on the EM7455 (FW23) for all 3.

An interesting note is that ipv4 might actually be handled differently on verizon - I had mentioned ...

Good question, but probably a difficult answer. The variables at play are the modem firmware, the drivers, and the router firmware. Something in there is adding to the latency. I doubt it is a problem with the MBIM protocol itself.

As for support of IPv6, again, I doubt that is a protocol level ...

This I am not sure of. I do know that the Cradlpoint dual SIM Card routers all use QMI.

Yes, until the latest stable GoldenOrb build or the newer WiFiX versions thereof, it would not accept QMI. The modem had to be configured in MBIM prior to installing the modem of GoldenOrb would not ...

Ah, I see. The Sierra command reference didn't discuss RMNET0 vs RMNET1 in detail and that they were tied to single vs dual SIMs. Does that mean you can't do dual SIMs with MBIM, or do you need to use 150D to enable that?

I meant I didn't know the history of why someone may have been told to ...

By using the AT Commands to place it back into MBIM mode. See the link below.

I assume because you did not view this TUTORIAL:

Naa I built this system like 3+ years ago, when MBIM was what everyone said to use. If I'm reading correctly MBIM does IPV6 and QMI only IPV4. So MBIM would be the ...

To place a MC7455 is QMI composition:

at!entercnd="A710"
at!usbcomp=1,1,10d
AT!reset

This will set it permanently to QMI until I change it back to MBIM?

Also, How do I change it back if say it doesn't let me connect?

Also what's the reason for us changing these to MBIM if we could have ...

Are you able to bring the equipment to the towers to see if that changes anything? Do you have a phone that shows better latency? Are you able to try QMI like Falias?

So I thought the idea was to run these modems in MBIM vs QMI as the towers see them as generic?

There was a huge reason for ...

JimHelms wrote: Fri Jun 21, 2019 4:45 pm Have you tested changing the DNS servers?

I run through opendns or Google dns servers. Plus my DL stays way higher when running through PIA vpn

Maybe something to ask the GoldenOrb people about?

Good job troubleshooting with a different provider and hardware.

I always thought my pings were 30-40, since speedtest shows that typically. I just ran ping on the router and the numbers seemed highly variable. Also ran them on Windows (firewall ...

I haven't done any of this, so I could be wrong on some of it, but I looked into it when I was setting my prepaid account up last month...
From my understanding, that post you linked with the ttl stuff allows you to use a tablet line without it being considered a hotspot... so it would get full ...

So update on my issue, I configured my PIA account onto the WG3526 and made sure it was all working. My ping is still terrible, but I'm no longer have 120kbs download speed. Ping is still in the 150 range. So looks like the pageplus unlimited is now a throttled source, even after my plan reset.

Ugg ...

should I try it out as 117? Vs 52?

iptables -t mangle -I POSTROUTING -o wwan0 -j TTL --ttl-set 52
iptables -t mangle -I PREROUTING -i wwan0 -j TTL --ttl-set 52

What app are you using on your phone to test this?

Here is my connection info, I really think B13 is just congested, hence why I'm ...

@serverside
I'm disheartened that you're having the issue too... that makes it less likely that it's something fixable... though maybe it's temporary if you've just started having it. (Hopefully!)
I'm in central VA...
I have decent reception, so I don't think that's it.
No, I tried the TTL ...

HAH I thought I was the only one. Something is going on with Verizon. 9+ months with your basically same setup, prepaid unlimited Verizon. Used to get 60-90ms ping on discord and games. Now this last week, it's now hitting minimum 150ms ping in discord and 200ms in games. I've reset the modem ...

Nope, cannot access the router at all. Normally I can hit the web GUI. But when it goes down, I can only hit it from a wired connection.

So as the title states when the Internet dies, wired connections can still browse to each other, but the wifi/wireless connections loose the ability to browse the lan, it's like they are being served a DHCP address by the internet gateway vs the router. I do have a domain created, but it is not a ...

Welp this one was an easy fix, their billing messed up and had my account in breach even though I have auto pay on. So it's fixed now. Check your accounts everyone lol

So as the title states, was working great for like 8 months, but last night around midnight, it dropped and has not connected back to the internet. I'm using a MVNO for verizon (tracphone). It shows connected to the tower no problem, but it won't connect to the net. Below is what's going on, I'm ...

So it's been about a month, I've got everything setup and running smoothly on WG3526 and MC7455, I have decent ping (120-150ms) but would like better speed and latency. I'm about 2miles from a verizon tower and am looking for an antenna that will be able to up everything. What would be the best ...

My current work around right now is LEDE/ROOTer running as the main router with DDWRT as the repeater for Wifi. Wifi is turned off on the LEDE/ROOTer router and on with the DDWRT box.

Hopefully it will be eventually stable enough for me to turn it on with the WG3526 box.

Just FYI if anyone runs into this, flashing from LEDE/ROOTER to the Archer C7 DDWRT requires you to use the factory to DDWRT image, you cannot use the DDWRT base image.

Just to update, the wifi issue is definitely not fixed. Its still failing to allow my Android devices connect. The laptops seem to work fine but phones and tablets not at all, even when forcing a static IP address they just drop constantly or never connect at all. Going to try the latest build ...

Default password is admin all lower case. Dunno if it's posted anywhere though.

So, you want ROOter to be LTE+WIFI+DHCP, and you want to reuse a second DD-WRT router you have as an AP only, with an ethernet cable running in between them?

Or are you not talking about using LTE functionality at all, and just wanting a second ROOter AP that is wired to your existing DD-WRT ...

So I've done this a good bit inside of DD-WRT but never with LEDE/ROOTer and am finding very little on how this is accomplished.

Basically I want to have my main router be DHCP to my second router via Hard Wired connection, then that router also running LEDE/ROOter be Wifi Access Point #2. I do not ...

Awesome thank you sir!

I need to take photos of mine as they have a new screen on the WG3526.

Also Jim is it possible to change the topic to WG3526 vs the WE so no one comes here and thinks this is for the WE.

Just to update this for anyone who is having issues with wifi to android or iphone devices.

Get a app called Wifi Analyzer on the play store (anything that can check channels), search for the least crowded channel. In my case, I was on channel 11 and had 2 other items on it as well. Changed it to ...

I might try this later, right now everything is working...sorta.

Ok so wifi works on everything BUT....android phones, which for some reason only seem to get a signal or connect IF I give it a static address otherwise DHCP it tosses like a hot sack of potatoes.

At this point I've done that so many damn times, after I read your comment and was like how the hell did I mess that up. I went and reflashed that image from the uploads, and did the OEM reset...just finished redoing my routes and everything is back up. Even have 5ghz again. Showing 20mw and 15mw ...

Wow....WG3526 4G LTE WiFi Router Dual Band (2.4GHz-5GHz) WiFi

That might be why....how did I screw that up ><

Any ideas? Right now I've got no wifi

might have to dig out the Archer c7 with lede on it so I can get WiFi going again.

Had to force it to go to .0.1 lan ip range, but that works now

It's also not allowing me to change the lan ip range to 0.1 vs 1.1

Nope same thing. Still showing 0db. Also password is admin for anyone who sees the thread. And when I flashed the firmware it pulled it up to the Chinese language screen and I had to flash it a second time

4th times a charm?

lol, spinning it up now and will let you know how it works out.

Super late reply on this, but I've reverted back to the one Dairyman sent me. So the Chinese menu popped up, your guide is way old and the menu has changed. Not hard to figure out though, so I got that taken care of.

So now that I'm on the earlier version of Rooter, YaY.

Bad news is....my Wifi ...

ok I'll give this a go later tonight.

The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform.

Getting this error, and it's if I pull the .bin file or upload the .zip

Ok I'll give it a go tonight. Thanks

Search found 88 matches