Wireless Joint

The NEX router will set the outgoing packets TTL/HL at the interface in the rule with POSTROUTING. So if you are using wwan0 (modem) then you should be good for all traffic.

I wrote up a full writeup. Never posted. Sheesh. LOL. Anyway Click on Edit button in line with LAN and WAN you will see an advanced tab. There is a checkbox for something mentioning DNS. Click that and the DNS custom DNS entry appears. Leave the DNS search domain and the DNS weight blank. For the ...

Hot off the press!

Update to this version:

https://drive.google.com/file/d/11Rpn6m ... sp=sharing

That will fix it for you.

Shoot MOFI a message and ask them where you enter AT commands.

Have you emailed SIMCOM?

Sweet! <HighFive>

Hmmm, no experience with it myself, but I've read that typically means the SIM/plan/account isn't 5G provisioned. If the device initially provisioned/registered to the SIM isn't 5G provisioned that could be an issue.

My guess is the cell booster is only boosting tmobile bands from a tmobile server. It isn't just boosting all cell towers radios in the area. They don't work like that

Most modems I've used on old Sprint plans that are now T-mobile, lately, including the Calyx SIMs, needed the modem imei to match the hotspot the SIM came in. (SierraKeygen bkerler might be a good think to lookup) You can also give a go at calling Tmobiles BUSINESS support line and tell them your ...

Private/incognito tabs every time for me. I've spent hours going WTF?!?!??! just to realize the browser cache wasn't clearing on exit.

Hmmm. So flashing a different firmware brought it back and then it left again? Did you flash the firmware like 3+times in a row to ensure some goofy setting isnt stuck in there causing trouble? Also, you may want to try and set the radio settings to a top or bottom channel, not auto, that isn't in ...

"AutoSel",1 means its choosing different APNs automatically based on the SIM card entered. Looking at your "List" output its chosen the "Commercial-TMO" PDP Context to load Tmobile APNs. If you want this to stop run: AT+QMBNCFG="AutoSel",0 Then: AT+QMBNCFG="Deactivate" Then: AT+CFUN=1,1 Then check ...

For the previous two years, I used to get 30 to 40 Mbs with seemingly no throttling on my Calyx supplied Franklin R910--but that was in the Sprint days. Have you seen any throttling recently? I haven't noticed. I don't use it as heavily as I used to, mostly just testing these days. It used to by my ...

Remove the last ,0 or ,1 and just do "NWSCANMODE",3 Factory restore is AT+QPRTPARA=3 then when the modem recovers, AT+QPRTPARA=1 You may want to contact Quectel directly for help setting the EP06A for data only setting for the ATT 3G sunset. There may be special commands that need to be ran. I'm not ...

Hmm, thats a good thought on the firmware, as I'm currently running; 1.8.8-20210531-131411 How are you staying up to date with the firmware releases? Does CUDY have a firmware updates page I could check periodically? Feeling a little gun-shy on updating, based on your mention of the latest not ...

Today, I for cat18 in place of 5G and plug and play I would go with the new LT18 router: https://thewirelesshaven.com/lt18 https://www.youtube.com/watch?v=nZAUY5kValY If you want to build a unit that can later be upgraded to 5G then yeah I would say the same thing with the EM160R-GL instead. You can ...

Did you modify the modem to match the identity of the hotspot? It seems to be a requirement now.

The LT18 has a better modem in side and has the ability to access and upgrade the cell antennas. AND it has 4 ethernet ports, etc, etc. It's functionally better. You shoul dbe bale to get the LT18 working with any of the carriers, but you may have to make some settings changes between SIM swaps to ...

You may want to ensure the modem is in MBIM mode: AT!USBCOMP? should say 1009, versus QMI which is 10D Also check that it is in fact using the APN you entered: AT+CGDCONT? and last make sure that you are using a generic firmware image or let the modem decide: AT!IMPREF="GENERIC" or AT!IMPREF="AUTO ...

best way I use is to SCP into the routers file system and manually edit the network config file. Reboot, done. WinSCP: https://ofmodemsandmen.com/winscp.html The file is located here: /etc/config/network Otherwise, in the UI make sure to open a second page with the new IP addr. When the router goes ...

vahnwinkle I gotchu. Get winSCP and putty if you don't have both apps for Windows : https://www.ofmodemsandmen.com/winscp.html (Im not much for Mac so if you use mac, find equivalents and adapt the instructions for your OS. Get the appropriate modem firmware update and unzip it somewhere you will ...

It's likely that the orbi and its EG18 is not dealing out an IPV6 only interface that is 1pv4 over ipv6 (CLAT/XLAT) enabled. The latest Tmobile network structure is pushing hard to IPV6 only, and most legacy devices can only use IPV4. I've not tested my new Tmo SIM from Calyx in the Orbi, but I'll ...

Simplest setup at the lowest price for a new setup, based on your question: https://thewirelesshaven.com/shop/route ... -and-play/

ChrisW wrote: ↑Thu Dec 16, 2021 5:36 pm Tried no change, I think i just got a bad router, tried a netgear LM1200 and connected fine, Cudy refunded my $$ and told me to keep it
Whats the command for QMI? AT+QCFG="usbnet",0?

yep except no ? mark

@Jflex113 I shot you an email.

Clarify for me. I am not familiar with the adb shell of the Quectel modems, at all ... are you running the ping from the host device command line here/above or is that via the adb shell? The gateway address on the routing table confuses me, as you are attempting to ping an external address (8.8.8.8 ...

There isn't one specifically, its kind of info that is in pieces all over the forum. The basis is. Download and install the latest Sierra Windows PC drivers and install on your PC. Download the latest firmware image of choice from here: https://source.sierrawireless.com/resources/airprime/minicard ...

NEXP1GOs are incoming, but maybe two weeks or so out.

Everything else should be in stock.

What would be the next best option if I didn't want to wait? I want to plug the router into a Netduma R2 without getting a double NAT The NEXS2GO with a 48V to 12V splitter. https://thewirelesshaven.com/shop/routers/cellular-internet-hotspot/with-wifi/dual-band-wifi/gigabit-ethernet/mini-pcie-slot ...

@Didneywhorl Okay thank you, I'm guessing the NEXS2GO has a feature that I can use it with a Netduma R2 without causing a double NAT? I guess I'd plug it into the Netduma WAN port after I run it through the poe brick. You would want to apply a static IP to the WAN and LAN ports of the NEXS2GO, then ...

Okay, I'll just pay extra for Wireless Haven to update the firmware. Worth noting that Wireless Haven will only update your firmware to the latest that supports all carriers, which at this point is quite old. it's probably worth learning how to update the firmware yourself if you can find the time ...

I pull the modem to flash it. You can do this with an adapter that will take the EM919x7690 modules, and a usb cable extension so you don't have to remove the antenna cables. I have never messed with the MOFI modem updater. I actually didn't know they had it built in. lol. I need to fire mine up ...

Means you should expect to see coverage outdoors.

Sierra5G-BandLocking-TWH-08-16-2022.pdf

I wrote this up to help.

@AlteredLogic , email info@thewirelesshaven and they'll get you squared up. I'll make sure of it.

I would turn off the PDP contexts: AT+QMBNCFG="autosel",0 ...and make sure you are using MBIM mode: AT+QCFG="usbnet",2 Then power cycle the router. Then when back, double check the Profiles. Shouldn't need all of those. The router itself isn't doing much other than supporting the modem to do its job ...

This is a tough one. So many variables. Likely the issue is a firewall issue not allowing the nest products to ping the home server, or vice versa, via IPV4 or IPV6 (ICMPv6). VPN services do not use IPv6, so that is likely the fail there if it has to be transmitted over IPv6. The latest routers use ...

You might have to do this via SSH CLI commands (openWRT should have all the how-to on just about anything). I believe Nick removed a lot of stuff from the Rooter/Goldenorb (same base as WiFiX) based firmware that he copied and added to/from originally for intsy. I haven't tested it in the last year ...

...should be no problems refunding the money for it, even half of it, ... I think I mis-understood this to mean full refund. :| My apologies... There is NOTHING in the returns policy that says you can't negotiate the terms of the refund on a returned system. It just says no 100% refunds for "non ...

Search my posts, I did a step by step on flashing Quectel modems while still in the router. Will 100% work on the wg1608.

The at command manual will give you the commands you seek. Or update the wg1608 firmware, rooter added band locking to the ui.

Dude that is such a rare modem! Man I love my EM20s! There aren't many out there that are still working (abused lil guys!), and damn few for sale now.

I have two still, or I'd snatch it!

People, don't pass on this.

No secret, it was just a simple powerful modem.

The MC7411 with the NEXQ6GO all day over the others. The MC7411 is "only" category 7 but it is based on a newer modem platform that is similar to the category 12 modems. (MDMx90 if I recall) I use the MC7411 in a lot of builds. It's been a great little modem. If you want a little bump in router and ...

This is fixed in the October release: https://thewirelesshaven.com/nexp1go-latest-firmware

Admin menu lock isn't functional and wasn't supposed to be there.

AT!IMPREF? !IMPREF: preferred image setting does not exist current fw version: 01.07.13.00 current carrier name: current config name: current subpri index: 000 fw version mismatch carrier name mismatch config name mismatch OK This is bad. You need to reflash the firmware. You said you "repaired ...

https://thewirelesshaven.com/docs/sierr ... -flashing/

Request sent.

I would set all bands back to unlocked then power cycle the router. See what happens. If it still acts goofy, I would turn off n71, and maybe b71. See how it works. Is it also setting up on stand alone n71? Where the UI shows n71 only? If so, you may want to lock out the SA n71 with: AT+QNWPREFCFG ...

WE826 .. question is, is it a WE826T2 or WE826Q. Probably find it in the system or kernel logs. One is a Qualcomm 9537 the other is a mediatek chip. Cant recall which.

T2/T

The Q uses a Qualcomm QCA9531

Monitor, as in when connected to the router, or remotely?

There is a firewall log i believe, and rooter is openWRT based so you can pretty much install any openWRT package on it. I've never done traffic analysis myself.

It might be that the thermo is setup to be pinged externally and not as a "man on the inside", and since cellular wireless uses CGNAt, there is no public facing IP. Maybe? I'm guessing that is why one brand would work for someone and the other wouldn't?

Just spitballing.

That should help yes, but you may experience slower speeds as running a VPN on the 400MHz single core 826 router base isn't real optimal. Wireguard is lightweight, but I'm just giving you a heads up that it might be noticeable.

Make certain you get a good geographically close VPS.

Quectel modems all use the same command to see the imei. Look for information on AT+EGMR

I don't tihnk forwarding is useless, I would go that route and play with firewall zone settings.

What port does the Thermostat use for it's cloud connection, regardless of IP address?

Maybe open up 5671, 5672, and 443 to allow all inbound and outbound?

THIS!

Love it!

I wondered if the cables would benefit from shielded coverings.

Nice work.

It's hard to say. I used to not get n41 to save my life, now I can only get it to do Stand alone n41 and not NSA n41 with the available lte bands. No hardware or settings changes. Aggravating. It's got to be how Tmobile is setting up the towers and bands.

im trying to figure out how to band lock my lbr20 to BAND 2 can anyone help me figure out what i need to do to be able to do so? Band locking method is in this tutorial that your posting in: https://wirelessjoint.com/viewtopic.php?p=12676#p12676 The modem is a Quectel EG18, and uses the same ...

I am using ZeroTier on various devices (windows, Mac, android, LT18) with great success. According to the Rooter website ZeroTier is available for the firmware. Is it part of the firmware for the NEXq6GO or can it be added. If so, how? It takes a few steps, but... https://github.com/mwarning ...

Lowest cost would be to modify the TMo router and add antennas like this one: https://thewirelesshaven.com/shop/antennas/outdoor/outdoor-cellular/mimo-directional-panel/700-3800mhz-cellular-8dbi-directional-4x4-mimo-antenna-%c2%b1-45-n-female-connectors/ or two of these: https://thewirelesshaven.com ...

Lowest cost would be to modify the TMo router and add antennas like this one: https://thewirelesshaven.com/shop/antennas/outdoor/outdoor-cellular/mimo-directional-panel/700-3800mhz-cellular-8dbi-directional-4x4-mimo-antenna-%c2%b1-45-n-female-connectors/ or two of these: https://thewirelesshaven ...

Yeah, the internal mini-pcie is USB2, whereas the USB port on the outside is USB3 (10x the max possible speed 480Mbps vs 4800Mbs)

Internal space is also too tight to fit it in there, properly.

Technically not talked here.

If you need to put an incorrect IMEI back to the number it should be, on a Quectel modem, you'll want to look up the AT command AT+EGMR

I just purchased this from wireless haven and have 3 questions. 1. When connecting the antennas does it matter what side I put the split lock and and the Lock washer. I assume the lock is on the outside and the split lock washer on the inside? Star washer inside, split on the outside. 2. There was ...

The problem is the Chinese manufacturers are choosing chips not supported by openWRT. If there is no official image for openWRT, Rooter generally wont spend time on making an image. Many of these IPQ chips have come out over the last few years, the Chinese manufacturers modify their 2015 toolchains ...

Antenna Modem

ANT1 = pri ant 1
ANT2 = pri ant 2

ANT3 = sec ant 0
ANT4 = sec ant 3

RG6 cable isn't the right Ohms. LTE antennas use 50 Ohm coax, RG6 is 75 Ohm. Unless there's some RG6 out there that is 50 Ohm?

The LAC value is a sort of grouping ID# of all the radios that are of the same broadcast service on a single tower, if I recall correctly. Finding the number can be tough. The Quectel EC25 (The modem inside the LT500) doesn't really support querying that specific metric, if I am not mistaken. I ...

I use the heck out of Tmo SIMs in all of my test rigs and full time rigs.

This bugger will work basically out of the box: https://thewirelesshaven.com/shop/route ... -rm520ngl/

Search found 664 matches