Wireless Joint

More to come.... Bare with me.

Getting started with the Router body. We gut the router...

Here are a few of the things needed to get going, already listed above.

I went back to my T-Mobile card because my Verizon data limit before throttling was reached. I have unlimited on both cards, but apparently the T-mobile card from OTR mobile doesn't get throttled. So, You're saying to put the Verizon card back in and change the TTL as stated above? I will research ...

Sure! I used this setup for nearly two years. Near the beginning of the year I upgraded to a Quectel EM20G modem and added a second panel, since the EM20G modem can do 4x mimo. The Quectel has had quirks, but its fast and works well. The MC7455 was great, except the MC7455 does not like to run ...

Modems in general can only connect to a single cellular provider at one time. They also can only connect to a single tower at one time. Carrier aggregation simply means aggregation or multiple channels over the same connection. MIMO allows for multiple physical pathways over the air. When travelling ...

Get a router Flash to r00ter Change appropriate settings Power Down Pop in SIM Pop in adapter Pop in Modem Attach proper antenna connectors to modem Power unit up Test connections The generic firmware is something that is needed on the modems, all of those modems listed have a generic firmware ...

That setup doesnt seem bad, if they are installing it. The router price seems decent but your paying for a modem you wont be using in it. The Telit LM960A18 is generally about $280 by itself, shipped. Mikrotik makes good equipment, but the firmware takes a PHD to understand. Once you figure it out ...

You likely went over the hotspot limit. Do you have ipv6 TTL(HL) set as well?

Your google drive images arent loading, they are hard to do without a link creator for them

Just use the attach file option at the bottom of the posting text box.

A few things. Clear out your APNs by running AT+CGDCONT? Then for every one that it returns in the output, run the following commands to blank them out: AT+CGDCONT=1 AT+CGDCONT=2 AT+CGDCONT=16 etc etc Running the command like that says set info at position 1 (2,3,16,etc) as follows ... <blank ...

Adm1jtg wrote: ↑Tue Oct 06, 2020 2:05 pm Hmmm current wifix versions have a date of 5-16 and current rooter versions are dated 3-1

i would try flashing one of the above versions

NEXQ6GO firmware is loaded with its own firmware. There is no updated version yet

The modem inside is a Telit LM960 modem if I recall correctly. It is'nt 5G ready as far as I know. For the AT commands you'll have to go with those. I';m fairly certain the ATTERM is a function of the router and will likely work fine with that modem. I would go with a full set of antennas, 4 matched ...

Leave it! lol.

QMI vs MBIM is kind of a moot issue. Go with what works.

Nice! What modem are you using in the m.2 slot?

It seems to be a silent proxy server issue they've caused. Basically certain major http ports, like 80, just stop transmitting. A simple reset fixes it. You can also force the modem to change bands to fix it.

The site has been completely moved to another server host. Its likely some users and posts have been lost.

I think your issue will be resolved if you place the SIM card in the slot on the side of the router, not in the adapter. This is how mine is setup.

The raspberry pi is a cool project to play with. I personally would only build a router out of it if you are a linux fan and love playing with the pi. If you are wanting to simply keep on a budget. I would go with a NEXQ6GO from thewirelesshaven.com. The EP06A drops right in. For the EP06A and the ...

Good call to mirror your antennas. I always recommend matched pairs, and always 2 where 2 can be afforded and used. 4 if you get all fancy with a high end modem.

The RM500Q-AE is what you want for 5G imo. Its the NSA version I've recently been told by user BillA. I would wait for the Quectel EM160. Its cat 16 4G with 4x4 MIMO.

If you just want a cheap LTE modem that does the job, then look at teh Quectel EP06, or some SIMCOM equivilents.

As a general reference. Your above pictures show the router is seeing the modem just fine for general purposes, but for some reason the AT command port is missing. This is on the modem, not the router. the router looks in a specific spot for the AT commands and no where else. If that port has been ...

Try setting the APN to IPV6 only? AT+CGDCONT=1,"IPV6","broadband" Make sure you clear out the other APNs that say "broadband" with AT+CGDCONT=<#ofAPNListed> Like this: AT+CGDCONT=3 There may be a way in the router, but I think the modem connection to the carrier controls this at the gateway. I think ...

1. Purpose for tethering a phone to a router via USB or WiFi The purpose for tethering a phone to a router via USB or WiFi, is to be able to use the phone's unlimited mobile data just like having an external cable/DSL/LTE modem connected to a router, with data speeds equal to the phone's mobile ...

First. The EM20 is a product no longer made. You'll have to get a rare new one or find a used one. The EM160 is soon to release and all the latest "5G" modems are 4x4 MIMO. That or the Telit LM960A18, Sierra 7690, and some of the SIMCOM and Fibocom modems are 4x4 MIMO. I only have experience so far ...

Good work!

So in the end, factory resetting the modem did the trick? That's great!

In order to get band71 does the aim card have to be from a phone with "5g"? Can you get an inexpensive tablet or phone with 4g lite and use that sim card and get band71 in the mofi4500 sim7. Ex. Get a low end tablet with 4g lite for $25 a month's and use it for unlimited internet. Or does the ...

Its what we all do. :) You can definitely add a router to your Verizon account. But the data only plans are exceptionally restrictive. Like 20GB a month for a buncha money more than its worth. IF you just need that, it's perfect. Most of us need more data, so we try trickery to mask the usage as ...

You could if you know Linux really well and know how to turn a Linux pc into a router. All you would need is the right drivers for the modems, which is almost included at this point. Or you could buy a gateway router with an M.2 or mPCIE interface and be "nearly" plug and play with openWRT ...

You should do just fine with the Visible SIM. Make sure you activate it in a phone first. The issues people have had with Verizon the most are using Verizon direct phone SIMs for data, and wondering why it isnt working for super cheap unlimited whole house Terabytes a month data. The other issues ...

I dont use boosters, but I think you are correct. The booster just amplifies along a particular frequency.

A high gain directional antenna should do the same, and with cleaner signal, for cheaper. Especially if for data only.

woodz wrote: ↑Fri Nov 06, 2020 9:31 pm If anyone finds a source for the HMF-SW23 pigtails please post a link.

thewirelesshaven.com is working on stocking them asap

http://wirelessjoint.com/viewtopic.php?f=12&t=5&hilit=firmware+recovery

Gotta hold it for about 10-15 seconds after applying power. Basically when the second light lights up.

http://wirelessjoint.com/viewtopic.php?f=12&t=5&hilit=firmware+recovery+method

Try that. It may take a few tries to get it working, the WG1608 can be finicky

When logged in via SSH, what commands are you sending to be able to send the AT commands to the modem?

Also what roddel007 said

FYI: thewirelesshaven.com is working on getting the special connectors/pigtails to allow adding pigtails for external antennas to the Tmobile home internet device.

I would love to get a heads-up if those MHF-SW23 connectors are ever acquired... comming here from Reddit and the FB group for TMobile Home ISP... oh ya HI! ;) Keep an eye on the thewirelesshaven.com site under SMA antenna pigtails: https://thewirelesshaven.com/product-category/cables/pigtail ...

Thanks for taking a look I'll monitor the thread "I" figured it out, via Jim helms suggestion ;), you have to downgrade the firmware on the EP06 to an older version. For whatever reason Quectel has changed the way their firmware is recognized on the USB bus. The WG3526P and the NEXQ6GO has been ...

Well done thank you to you and Jim both. I'm currently looking for older firmware to give this a try. If you (or anyone) has a source to download the firmware I'd be grateful. Also, is there a different procedure to downgrade the firmware on this modem, or does it work the same as an upgrade? I can ...

An alternative fix Ive tested. The same as here: http://wirelessjoint.com/viewtopic.php?f=8&t=1085&p=7330&hilit=custom+modem+ports#p7330 Set the Modem--> Custom Modem Ports, as such: NEXR5GOCustomModemPorts.png then click Save and Apply Then you have to putty into the router, login with root and ...

I'm actually looking into stocking these, mostly for remote camera systems, but also to see if they can be upgraded.

I have a question related to setting up dual MIMO 2x2 directional/yagi antennas. But I am also researching band locking to lock my modem into the best channel/band. My question: Can 2x2 MIMO antenna setup work with band-locking or are these impossible to use together? Not sure how MIMO works? Does ...

I would guess 65 or 66. Set it and check to see if your data is counting as hotspot data or not. Dont forget the ipv6 'ttl' (HL)

Your iphone7 has 4x4 MIMO antennas and a category 16 modem, with at least 3xCA capability. Your SIM7 is a category 3 modem with 2x2 MIMO antennas and no CA capability and limited bands in its list. I would get an thewirelesshaven.com NEXR5GO router and a Quectel EM12 modem (dont forget the minipcie ...

thewirelesshaven.com's NEXR5GO router with a Quectel EM12 or Sierra EM7565 modem. https://thewirelesshaven.com/shop/routers/wifix-routers/nexr5go-cellular-router-poe-with-dual-band-2-4ghz-5-8ghz-wifi/ https://thewirelesshaven.com/shop/modems/quectel-modems/quectel-em12-g-cat12-m-2-modem-2/ https ...

I would revert to the original firmware, via recovery.

This is not the place for troubleshooting your modems and routers, please post in the appropriate support location.

Its TTL settings, and the MOFI copied ours

Under Network-->Firewall-->Custom TTL settings

Its not making it look like a cell phone, its just changing the TTL, as that is the current way some carriers see the traffic as hotspot or on device data.

The latest update says the special antenna pigtails from IPEX will take 6-8 weeks to be made and shipped. Mid to late January is what is being quoted.
This is a brand new product line and is going to take much longer than other items to get manufactured and procured.

Ive not seen this. Might just be dead. Your modem is likely fine though. Did you try a different power cord/supply, just for giggles?

There's apparently a 12/02 goldenorb up now... Anyone done any analysis on the differences? Changelogs sure would be nice, but with all the routers they're supporting I suppose that would be far too much to ask. I think it was just an attempt to get the 5Ghz Wifi working. The changelogs are via ...

56387f wrote: ↑Sat Dec 05, 2020 1:55 am ... CA does not kick in under heavy load - can it be that CA for B2/B4 is not supported by the tower I am connected to? That's my main question ;-(

100% yes. It happens, and even can be there one day and gone the next.

... APN: AT+CGDCONT? +CGDCONT: 1,"IPV4V6","VZWINTERNET","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0 OK Try adding the IP APN: AT+CGDCONT=2,"IP","vzwinternet" Band: AT+QCFG="band" +QCFG: "band",0x260,0x2000000000000101a,0x0 OK What else can I check? Why are you band locked out of so many bands? I ...

Changing to ECM mode sometimes requires you to SSH in and run AT commands manually, especially to change it back to QMI or MBIM. Try that one as a last ditch effort.

I think Verizon likes when the router and modem communicate in MBIM, though it really shouldn't matter.

gscheb wrote: ↑Sat Dec 05, 2020 8:23 pm Agree be careful about that ecm mode. Can be a pain to get out of. I try to avoid that all together personally.

Agreed. Last ditch effort.
When it works it works really well. It seems to reconnect, when connection lost or going mobile, very fast in ECM mode.

If you want to keep the linkzone as the device you can try to get an externally powered USB3 cable that is very long maybe? Does the Netgear router support USB tethered modems? Some routers do support this. The thewirelesshaven.com routers do. Most any router that can run openWRT firmware or its ...

I can confirm as well. Band 41, 25, and 26 in some areas are straight GONE, or neutered. It may come back, but Tmobile is wreaking havoc on the Sprint networks. You should get on Sprints online chat feature for tech support and ask for the status of your tower.

dubgdaddy wrote: ↑Tue Dec 08, 2020 9:30 am Okay, updated firmware and it now sees the modem. It connects and sees the imei, etc. I've updated the APN to broadband but still no internets. What else am I missing?

Just checked, they are in stock right now: https://thewirelesshaven.com/product-category/mod ... el-modems/

The fact that it shows in debug tells me the router just isn't giving it the ports needed to act appropriately. I have noticed on the whirlpool forums that the rooter firmware base has had a history of recognition issues with the EP/EM06 modems. All fixed with port setup commands. I was able to ...

Hello, I just switched from a mofi 4500v2 to a WG3526-P + EM7411 CAT-7. I know this thread is titled for MC7455/EM7455 but was hoping the AT! commands are the same with 7411. With the mofi locked to B4 T-Mobile I was averaging 30-32mb down (a 3.5 miles on a hill from tower, as high as 55mb as lower ...

AT+CGDCONT? +CGDCONT: 1,"IPV4V6","ndo","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0 OK This is good, though I would add an pdp context (APN entry) for IP4 only. AT+CGDCONT=2,"IP","ndo" AT+CGATT? +CGATT: 0 OK This is saying no APN is active/attached You can have it list all pdp context entries and ...

It shouldn't make a difference. but try putting the modem in QMI mode. The mode protocol should just be for the modem to router communication but somehow it also affects the cell network registration. I don't really understand the difference, though I have read up on it some. A bit over my head for ...

They may have changed the APN to x.ispsn, which is ipv6 only and a major arse pain. Call and ask for the APN that SIM is provisioned to.

T mobile is likely the easiest for getting on the network with your own gear. Verizon is a pain, but not un-doable. My favorite router modem setup right now is the WiFiX NEXR5GO router with a Sierra Wireless EM7565 modem. Or if you want/need bands 14 AND 71 then the Sierra EM7411 is the one. It has ...

The latest version fw for the EM160R-GL is version A04. (EM160RGLAUR02A04M4G)

Though I do not yet have a copy, I only have A03 on file. The newest modems received already have A04 on them.

I always add a dedicated WiFi access point or mesh system that plugs in via ethernet to the router, and turn off the routers wifi radios to give full power to the modem. Its really the best way in my opinion.

The EM160 doesn't use that command, so its just something to ignore. The newest Quectel modems, like the EM120 and EM160 as well as the RM5xx modems are using a new command set for a lot of things, and though those are being added to the firmware of many routers, the old command still run in the ...

Thank you! That's good info to have and glad to hear that it isn't anything unusual. I'll plan to leave it as is since it doesn't seem to be effecting it's operation. I've downloaded the "Quectel_EG12_EM12_EG18_AT_Commands_Manual_V1.0_Preliminary_20180706". Do you know if there has been an updated ...

As some of you may know, or have recently found out, the newest Quectel modems (EM160, EM120, RM500, RM510, RM502) do NOT use all of the same AT commands as the predecessor modems. Here are a list of a few new commands and what they should do, and a list of commands that I've found not working ...

No worries. Most would prob feel the same way looking at the gear you rock with all day long. :) The biggest issue with these connections is that most of the info is hidden or too discreet to understand plainly. Visible likes to see MBIM modem protocol. AT command: AT+QCFG="usbnet",2 then Clear out ...

I think that will work perfectly, I think, and allow you to use another modem on your system if you want to add a second modem.

It should be fine to use an adapter, but I would get a usb to m.2 direct adapter.

Thanks for sharing that. Good stuff. QFlash: https://drive.google.com/file/d/10Yyp2pr0zOg1hMG1itnmt1rz0oR_aera/view?usp=sharing Unzip it and find the QFlash.exe file and run it. Windows drivers: https://drive.google.com/file/d/1Demcq6rn8liMWZG2CaYidoJ_J1p_D6Hw/view?usp=sharing Install the drivers on ...

Hi Didney, this is what Quectel sent me for firmware: https://arkomasurvey-my.sharepoint.com/:u:/p/joshkelly/EfcNUHd4D91MsMN_odY2kNQBo8AhsxEplOkEwrxiLDTFOA?e=4nngYo Not sure how to get it in a format for the flash tool though. Quectel did say to use tool 4.19 or higher to flash. That is the latest ...

Just make sure, based on your previous posts, we are clear on this new post:

You've got a Quectel EM12G, a Visible SIM that has been activated and confirmed working in a cell phone, and a NEXR5GO router with stock MOFI Paddle antennas? (I didn't see which antennas you have tbh)

kzaudio wrote: ↑Thu Dec 17, 2020 11:59 pm @Didneywhorl ... I guess I'm doing something wrong. Maybe day 4 will be my day. Thanks man.

Which antennas, that are connected to the modem, are you using?

Search found 664 matches