Configuring GoldenOrb with Sierra Wireless Modem

[JimHelms]

This tutorial assumes:

1. The modem has been installed in the router.

2. WiFiX/GoldenOrb firmware is loaded on the router.

STEP THREE: CONFIGURING THE ROUTER AND MODEM

Log in the router's user interface at 192.168.1.1

NOTE: It may be necessary to clear the browser cache if any issue is experienced with accessing the login screen. This can normally be done by placing your mouse pointer to the top of the web browser and hitting the CTRL and F5 keys at the same time or refer to THIS site.

The login user name is root and leave the password blank since no password is required on the newer builds of WiFiX/GoldenOrb. If it still insist on a password, try admin

NOTE: If the WiFi SSID is broadcasted as rooter the WiFi default password is rooter2017 or rooter2019.

If the WiFiX is broadcasted as wifix use 12345678

Once logged into the router:

Go to MODEM > CONNECTION PROFILE > GENERAL > APN and:

• Type in the APN required for your carrier data plan

• Set the AUTHENTICATION PROTOCOL to NONE.

• SAVE & APPLY

Setting the APN.png

A few of the more common carrier APN’s are provided below:


AT&T

Code: Select all

broadband

Verizon

Code: Select all

vzwinternet

T-Mobile

Code: Select all

fast.t-mobile.com

Sprint

Code: Select all

r.ispsn

Sprint

Code: Select all

n.ispsn

Go to SYSTEM > SYSTEM > GENERAL SETTINGS and Click on SYNC WITH BROWSER and set TIMEZONE to your timezone. SAVE & APPLY.

Sync and Update Time Zone.png

Go to SYSTEM > ADMINISTRATION > ROUTER PASSWORD and set your router login password. SAVE & APPLY.

Update Password.png

Depending on the type of plan the SIM Card is provisioned for (i.e., if it has limited hotspot data) it may be beneficial to use custom TTL settings.

Go to NETWORK > FIREWALL > CUSTOM TTL SETTINGS (at top of page) > SETTINGS and ENABLE. Set TTL VALUE to 65 (or 64). SAVE & APPLY.

Set Custom TTL Rules.png

NOTE: It appears TTL of 65 (because of the pre and post routing) work across the board of carriers. If the data usage is still appearing in the carrier’s account as hotspot data usage, try TTL 64. Most data only plans do not require use of the custom TTL rules.

Unplug power from the router.

Insert your SIM card into the router. Note, be sure the SIM card is fitting properly into the SIM Card adapter—not loose but not too tight. The tits/tabs on all 4 sides of the SIM card should be removed via emery board or sand paper.

Power up the router and login using your new password.

Give it a couple of minutes to configure and stabilize and you it should connect with internet service.

NOTE: You will find it useful (and informative) to watch the connection process in live-time at MODEM > DEBUG INFORMATION AT-COMMAND EXECUTION.

Modem Debug Information.png

AT THIS POINT the majority of new users should be connected and good to go

ADVANCED MODEM CONFIGURATION FOR SIERRA WIRELESS MODEMS (ONLY):

Once an internet connection is established the MC7455 (if new) will be operating in QMI composition.

Running a Sierra Modem (or other modem) in QMI mode has only been possible with the later OpenWRT kernel builds of GoldenOrb. Some users prefer QMI while others prefer operating the modem in MBIM.

At this point you may first wish to see how the router performs with the modem in QMI mode.

Some of our MEMBERS discovered that QMI reduces the Latency over MBIM.

The decision to use MBIM over QMI is often determined by whether your SIM Card and data plan is capable of obtaining an IPV6 address for the internet connection. QMI currently (or at least on this GoldenOrb version) does not handle IPV6—which MAY OR MAY NOT be available with any particular cellular data plan.

To place the MC7455 in MBIM mode, go to MODEM > MISCELLANEOUS > AT-COMMAND TERMINAL

AT-Command Terminal.png

And, run the following commands (one command at a time, waiting for a response before issuing the next):

WARNING: DO NOT USE THIS CODE on an EM7565. It is different and listed below.

Code: Select all

at!entercnd="A710"
at!usbcomp=1,1,1009
at!reset

NOTE: The first command “….A710” is the authorization, the second is for MBIM, and the third applies the commands and reboots the modem.

When changing a MC7455 to MBIM mode, I personally like manually programming most other commands (i.e., IPV4V6 APN, enabling IPV6, and locking to LTE service only). I will use AT&T’s broadband APN for this demonstration:

Code: Select all

at!entercnd="A710"
at!usbcomp=1,1,1009
at+cgdcont=1,"ipv4v6","broadband"
At!custom="IPV6ENABLE",1
at!selrat=06
at!reset

To return the MC7455 to QMI mode:

Code: Select all

at!entercnd="A710"
at!usbcomp=1,1,10D
at!reset

If you are using the EM7565 CAT12 modem, a slight modification is required. To place this modem in MBIM requires:

Code: Select all

at!entercnd="A710"
at!usbcomp=1,3,1009
at!reset

While returning the EM7565 back to QMI mode requires:

Code: Select all

at!entercnd="A710"
at!usbcomp=1,3,10D
at!reset

If these steps were followed, it is now a matter of process of elimination to pin point issues. If a problem still persist, the next step is to examine the strength and quality of the cellular signals at your router.

This is accomplished by running the command:

Code: Select all

AT!GSTATUS?

IF YOU REQUIRE ASSISTANCE WITH AN ISSUE, please submit a separate topic FULLY DETAILING the issue (and the steps you've taken) in the QUESTIONS and SUPPORT section.

[DonJuane]

Hi, is the 7511 required to use the same notes above as seen for the 7565? I have decided to try the 7511 for a travel modem for a while since it still has a full suite of 3G bands still supported (for lower tech countries) but all the 7565 + B14 from what I have read (likely also you so will more info on AT commands and other info be on the way soon for the 7511? Thanks!!!