I finally received the USB3.0 to M.2 (NGFF) Adapter with Side SIM Card Slot yesterday, and tried a few things with it. The first thing I noticed was that syslog on my linux systems indicated the modem was not booting without a SIM installed, so this now makes sense why I needed the SIM slot on the adapter.
Installed the SIM on the adapter and tried again in multiple VM instances of CentOS and Ubuntu linux, and it still wouldn't appears as a device in /dev (despite it showing as expected in lsusb and syslog), so I just said, "**** it" and tried windows. It worked the first time there, so I re-ran the firmware updater as directed and it reported success, so I immediately disconnected it.
Now I've got it back in the ZBT-WE826, and it still can't establish a cellular connection withe the AT&T SIM that works in my MOFI.
Here are some diagnostic commands since the firmware was updated:
Code: Select all
at!impref?
!IMPREF:
preferred fw version: 01.09.04.00
preferred carrier name: GENERIC
preferred config name: GENERIC_002.019_000
preferred subpri index: 000
current fw version: 01.09.04.00
current carrier name: GENERIC
current config name: GENERIC_002.019_000
current subpri index: 000
OK
at!image?
TYPE SLOT STATUS LRU FAILURES UNIQUE_ID BUILD_ID
FW 1 GOOD 2 0 0 ?_? 01.08.04.00_?
FW 2 GOOD 1 0 0 ?_? 01.07.02.00_?
FW 3 GOOD 3 0 0 ?_? 01.09.04.00_?
FW 4 EMPTY 0 0 0
Max FW images: 4
Active FW image is at slot 3
TYPE SLOT STATUS LRU FAILURES UNIQUE_ID BUILD_ID
PRI FF GOOD 0 0 0 002.008_004 01.07.02.00_ATT
PRI FF GOOD 0 0 0 002.019_000 01.09.04.00_GENERIC
PRI FF GOOD 0 0 0 002.001_000 01.08.04.00_SIERRA
PRI FF GOOD 0 0 0 002.015_001 01.08.04.00_VERIZON
Max PRI images: 50
OK
ati
Manufacturer: Sierra Wireless, Incorporated
Model: EM7565
Revision: SWI9X50C_01.09.04.00 6d3218 jenkins 2019/02/26 20:33:22
IMEI: 353533100177925
IMEI SV: 9
FSN: UF921273890215
+GCAP: +CGSM
OK
at!priid?
PRI Part Number: 9908685
Revision: 002.003
Customer: Generic-M2M
Carrier PRI: 9999999_9907259_SWI9X50C_01.09.04.00_00_GENERIC_002.019_000
OK
at!pcinfo?
OK
State: Online
LPM voters - Temp:0, Volt:0, User:0, W_DISABLE:0, IMSWITCH:0, BIOS:0, LWM2M:0, OMADM:0, FOTA:0, RFCAL:0
LPM persistence - None
OK
at!entercnd="A710"
at!priid?
PRI Part Number: 9908685
Revision: 002.003
Customer: Generic-M2M
Carrier PRI: 9999999_9907259_SWI9X50C_01.09.04.00_00_GENERIC_002.019_000
Carrier PRI: 9999999_9907258_SWI9X50C_01.07.02.00_00_ATT_002.008_004
Carrier PRI: 9999999_9908789_SWI9X50C_01.08.04.00_00_SIERRA_002.001_000
Carrier PRI: 9999999_9907257_SWI9X50C_01.08.04.00_00_VERIZON_002.015_001
OK
And here are two of the relevant logs from the WE826 after booting it with the updated modem and AT&T SIM:
Code: Select all
[ 0.000000] Linux version 4.14.63 (dairyman@Compaq-Pro-6300) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7258-5eb055306f)) #0 Thu Aug 16 07:51:15 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ZBT-WE826 (16M)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 8044aae0, node_mem_map 81000040
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00038000
[ 0.000000] Readback ErrCtl register=00038000
[ 0.000000] Memory: 125016K/131072K available (3400K kernel code, 175K rwdata, 824K rodata, 200K init, 216K bss, 6056K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000013] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.007589] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.073550] pid_max: default: 32768 minimum: 301
[ 0.078266] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.084646] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.097450] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.106987] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.112975] pinctrl core: initialized pinctrl subsystem
[ 0.118581] NET: Registered protocol family 16
[ 0.606915] mt7620-pci 10140000.pcie: PCIE0 no card, disable it(RST&CLK)
[ 0.613411] mt7620-pci: probe of 10140000.pcie failed with error -1
[ 0.636117] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.641513] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.647928] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.653300] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.659674] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.664964] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.675439] clocksource: Switched to clocksource systick
[ 0.681854] NET: Registered protocol family 2
[ 0.686946] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.693673] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.699892] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.706170] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.711794] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.718196] NET: Registered protocol family 1
[ 0.722387] PCI: CLS 0 bytes, default 32
[ 0.724982] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.731672] Crashlog allocated RAM at address 0x3f00000
[ 0.738343] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.750279] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.755925] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.774720] io scheduler noop registered
[ 0.778525] io scheduler deadline registered (default)
[ 0.784421] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.791736] console [ttyS0] disabled
[ 0.795188] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.804860] console [ttyS0] enabled
[ 0.811889] bootconsole [early0] disabled
[ 0.820614] cacheinfo: Failed to find cpu0 device node
[ 0.825898] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.836712] spi spi0.0: force spi mode3
[ 0.850718] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.855586] 4 fixed-partitions partitions found on MTD device spi0.0
[ 0.862068] Creating 4 MTD partitions on "spi0.0":
[ 0.866977] 0x000000000000-0x000000030000 : "u-boot"
[ 0.872961] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.879334] 0x000000040000-0x000000050000 : "factory"
[ 0.885343] 0x000000050000-0x000001000000 : "firmware"
[ 2.695417] random: fast init done
[ 2.795170] 2 uimage-fw partitions found on MTD device firmware
[ 2.801242] 0x000000050000-0x0000001b8e78 : "kernel"
[ 2.807256] 0x0000001b8e78-0x000001000000 : "rootfs"
[ 2.813107] mtd: device 5 (rootfs) set to be root filesystem
[ 2.820384] 1 squashfs-split partitions found on MTD device rootfs
[ 2.826765] 0x00000081d000-0x000001000000 : "rootfs_data"
[ 2.833983] libphy: Fixed MDIO Bus: probed
[ 2.842846] gsw: setting port4 to ephy mode
[ 2.847414] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 2.854132] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 2.863148] rt2880_wdt 10000120.watchdog: Initialized
[ 2.869677] NET: Registered protocol family 10
[ 2.878045] Segment Routing with IPv6
[ 2.881912] NET: Registered protocol family 17
[ 2.886571] 8021q: 802.1Q VLAN Support v1.8
[ 2.908821] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.917170] Freeing unused kernel memory: 200K
[ 2.921702] This architecture does not have kernel memory protection.
[ 4.679240] init: Console is alive
[ 4.682947] init: - watchdog -
[ 8.797655] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 9.210055] usbcore: registered new interface driver usbfs
[ 9.215866] usbcore: registered new interface driver hub
[ 9.221407] usbcore: registered new device driver usb
[ 9.232714] exFAT: Version 1.2.9
[ 9.269069] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.285127] SCSI subsystem initialized
[ 9.294476] ehci-platform: EHCI generic platform driver
[ 9.310222] phy phy-usbphy.0: remote usb device wakeup disabled
[ 9.316280] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 9.320829] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 9.326736] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 9.334941] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 9.349801] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 9.357215] hub 1-0:1.0: USB hub found
[ 9.361501] hub 1-0:1.0: 1 port detected
[ 9.369185] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.377421] ohci-platform: OHCI generic platform driver
[ 9.383129] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 9.390134] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 9.398300] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 9.431849] hub 2-0:1.0: USB hub found
[ 9.436132] hub 2-0:1.0: 1 port detected
[ 9.443382] uhci_hcd: USB Universal Host Controller Interface driver
[ 9.463487] MTK MSDC device init.
[ 9.487907] mtk-sd: MediaTek MT6575 MSDC Driver
[ 9.498050] usbcore: registered new interface driver usb-storage
[ 9.507962] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 9.519686] init: - preinit -
[ 9.642430] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 9.982648] hub 1-1:1.0: USB hub found
[ 9.987937] hub 1-1:1.0: 4 ports detected
[ 10.541718] usb 1-1.3: new high-speed USB device number 3 using ehci-platform
[ 10.743140] usb 1-1.3: config 1 has an invalid interface number: 12 but max is 3
[ 10.750734] usb 1-1.3: config 1 has an invalid interface number: 13 but max is 3
[ 10.758328] usb 1-1.3: config 1 has an invalid interface number: 13 but max is 3
[ 10.765898] usb 1-1.3: config 1 has no interface number 1
[ 10.771413] usb 1-1.3: config 1 has no interface number 2
[ 11.039426] random: procd: uninitialized urandom read (4 bytes read)
[ 11.539848] 8021q: adding VLAN 0 to HW filter on device eth0
[ 12.872892] mount_root: loading kmods from internal overlay
[ 12.942275] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 12.951616] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 16.510689] jffs2: notice: (410) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (2 unchecked, 0 orphan) and 50 of xref (0 dead, 0 orphan) found.
[ 16.527515] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 16.593471] block: extroot: not configured
[ 17.766400] jffs2: notice: (408) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (2 unchecked, 0 orphan) and 50 of xref (0 dead, 0 orphan) found.
[ 19.587467] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 19.654246] block: extroot: not configured
[ 19.660631] mount_root: switching to jffs2 overlay
[ 19.727398] overlayfs: upper fs does not support tmpfile.
[ 19.737942] urandom-seed: Seeding with /etc/urandom.seed
[ 20.032040] procd: - early -
[ 20.035086] procd: - watchdog -
[ 20.753149] procd: - watchdog -
[ 20.756656] procd: - ubus -
[ 21.340829] random: ubusd: uninitialized urandom read (4 bytes read)
[ 21.578327] random: ubusd: uninitialized urandom read (4 bytes read)
[ 21.761767] random: ubusd: uninitialized urandom read (4 bytes read)
[ 22.577251] random: ubusd: uninitialized urandom read (4 bytes read)
[ 22.588820] random: ubusd: uninitialized urandom read (4 bytes read)
[ 22.595376] random: ubusd: uninitialized urandom read (4 bytes read)
[ 22.619694] procd: - init -
[ 23.733121] kmodloader: loading kernel modules from /etc/modules.d/*
[ 23.879569] tun: Universal TUN/TAP device driver, 1.6
[ 23.903595] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 23.935795] Netfilter messages via NETLINK v0.30.
[ 23.951258] ip_set: protocol 6
[ 24.063277] u32 classifier
[ 24.066050] input device check on
[ 24.069848] Actions configured
[ 24.088866] Mirror/redirect action on
[ 24.112749] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 24.149213] fuse init (API version 7.26)
[ 24.173755] usbcore: registered new interface driver cdc_wdm
[ 24.194507] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 24.202751] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 24.233654] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 24.258289] ctnetlink v0.93: registering with nfnetlink.
[ 24.467827] usbcore: registered new interface driver usblp
[ 24.487248] usbcore: registered new interface driver usbserial
[ 24.493394] usbcore: registered new interface driver usbserial_generic
[ 24.500187] usbserial: USB Serial support registered for generic
[ 24.615491] xt_time: kernel timezone is -0000
[ 24.638798] usbcore: registered new interface driver cdc_ether
[ 24.668787] usbcore: registered new interface driver cdc_ncm
[ 24.817628] usbcore: registered new interface driver huawei_cdc_ncm
[ 24.887651] PPP generic driver version 2.4.2
[ 24.895544] NET: Registered protocol family 24
[ 24.903984] usbcore: registered new interface driver qmi_wwan
[ 24.913885] usbcore: registered new interface driver rndis_host
[ 24.944917] usbcore: registered new interface driver sierra
[ 24.950807] usbserial: USB Serial support registered for Sierra USB modem
[ 24.961675] usbcore: registered new interface driver sierra_net
[ 25.009214] cdc_mbim 1-1.3:1.12: cdc-wdm0: USB WDM device
[ 25.015883] cdc_mbim 1-1.3:1.12 wwan0: register 'cdc_mbim' at usb-101c0000.ehci-1.3, CDC MBIM, 82:2b:84:ca:de:67
[ 25.026605] usbcore: registered new interface driver cdc_mbim
[ 25.081402] usbcore: registered new interface driver option
[ 25.087185] usbserial: USB Serial support registered for GSM modem (1-port)
[ 25.185561] usbcore: registered new interface driver qcserial
[ 25.191627] usbserial: USB Serial support registered for Qualcomm USB modem
[ 25.200291] qcserial 1-1.3:1.0: Qualcomm USB modem converter detected
[ 25.207375] usb 1-1.3: Qualcomm USB modem converter now attached to ttyUSB0
[ 25.217011] qcserial 1-1.3:1.3: Qualcomm USB modem converter detected
[ 25.224101] usb 1-1.3: Qualcomm USB modem converter now attached to ttyUSB1
[ 25.268253] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 25.275651] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 25.283577] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 25.291292] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 25.321278] usbcore: registered new interface driver rt2800usb
[ 25.348540] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 41.832185] 8021q: adding VLAN 0 to HW filter on device eth0
[ 41.861349] br-lan: port 1(eth0.1) entered blocking state
[ 41.866913] br-lan: port 1(eth0.1) entered disabled state
[ 41.872870] device eth0.1 entered promiscuous mode
[ 41.877768] device eth0 entered promiscuous mode
[ 42.043326] br-lan: port 1(eth0.1) entered blocking state
[ 42.048912] br-lan: port 1(eth0.1) entered forwarding state
[ 42.054810] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 43.038284] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 51.621895] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 51.632708] br-lan: port 2(wlan0) entered blocking state
[ 51.638217] br-lan: port 2(wlan0) entered disabled state
[ 51.644056] device wlan0 entered promiscuous mode
[ 51.649022] br-lan: port 2(wlan0) entered blocking state
[ 51.654467] br-lan: port 2(wlan0) entered forwarding state
[ 53.013028] br-lan: port 2(wlan0) entered disabled state
[ 53.778319] ieee80211 phy0: rt2800_config_txpower_rt6352: Warning - ignoring EEPROM HT40 power delta: -2
[ 53.815519] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 53.822289] br-lan: port 2(wlan0) entered blocking state
[ 53.827717] br-lan: port 2(wlan0) entered forwarding state
[ 71.580749] random: crng init done
[ 71.584241] random: 3 urandom warning(s) missed due to ratelimiting