ps
1st post here after lurking and finding a lot of useful information here.
Nighthawk M1 mr1100
Nighthawk M1 mr1100
I have 2 Nighthawk M1's. One is unbranded and the other is the AT&T version. The unbranded M1 has ip passthrough options on the dashboard while the AT&T does not. I have used the unbranded M1 and band locked it while connecting to my Nighthawk r7800 router to set DHCP. Can I set IP passthrough on the AT&T version? Would it be useful to connect both M1's and bridge the connections? If so some information or tips would be helpful.
ps
1st post here after lurking and finding a lot of useful information here.
ps
1st post here after lurking and finding a lot of useful information here.
Re: Nighthawk M1 mr1100
Hmm...I was hoping for an answer to this too, as you can find the
AT&T-branded version used cheaper than the Netgear-branded ones.
According to AT&T's s website, there should be IP pass through
mode available on their version(s). It is described on page 54 of
teh manual:
https://www.att.com/ecms/dam/att/device ... 00-QSG.pdf
Excerpt:
Enable IP Pass-Through Mode
To turn off the mobile router functionality and assign the network IP address directly to the attached device,
enable IP pass-through.
If you make this change, the attached device restarts using a different driver configuration.
WARNING:
If you enable this feature, WiFi is disabled and you must use a USB cable to
tether the device.
This feature is available to Windows computer users. If you are a Mac user, do not
enable this option because you will be unable to access your device.
Note
To enable IP pass through mode:
1. From a computer that is connected to your network, launch a web browser.
2. Enter http://attwifimanager or http://192.168.1.1.
A login page displays.
Specify Mobile Router Network Settings
54
Nighthawk® LTE Mobile Hotspot Router Model MR1100
3. Enter the administrator login password.
The password is case-sensitive.
The dashboard displays.
4. Select SETTINGS > Setup > Router Setup.
The ROUTER SETUP page displays.
5. Select the IP PASSTHROUGH ON button.
The default selection is AUTO
AT&T-branded version used cheaper than the Netgear-branded ones.
According to AT&T's s website, there should be IP pass through
mode available on their version(s). It is described on page 54 of
teh manual:
https://www.att.com/ecms/dam/att/device ... 00-QSG.pdf
Excerpt:
Enable IP Pass-Through Mode
To turn off the mobile router functionality and assign the network IP address directly to the attached device,
enable IP pass-through.
If you make this change, the attached device restarts using a different driver configuration.
WARNING:
If you enable this feature, WiFi is disabled and you must use a USB cable to
tether the device.
This feature is available to Windows computer users. If you are a Mac user, do not
enable this option because you will be unable to access your device.
Note
To enable IP pass through mode:
1. From a computer that is connected to your network, launch a web browser.
2. Enter http://attwifimanager or http://192.168.1.1.
A login page displays.
Specify Mobile Router Network Settings
54
Nighthawk® LTE Mobile Hotspot Router Model MR1100
3. Enter the administrator login password.
The password is case-sensitive.
The dashboard displays.
4. Select SETTINGS > Setup > Router Setup.
The ROUTER SETUP page displays.
5. Select the IP PASSTHROUGH ON button.
The default selection is AUTO
-
Rich Hathaway
- Posts: 622
- Joined: Mon Mar 08, 2021 2:41 pm
- Has thanked: 12 times
- Been thanked: 214 times
Re: Nighthawk M1 mr1100
Ip passthrough is available on the AT&T firmware, if its not on yours you may have a very old, perhaps the first build or something custom on yours but you can load the generic firm on it, those .spk's are on the web for free dl
