shwaba wrote: Wed Sep 04, 2019 12:49 pm Thanks guys for the quick responses. The LAN/WAN speed was a definite oversight. I'll be putting a order in for a WG3526 and see what kind of speed I can get out of that.

Keep us updated!

swwifty wrote: Tue Jul 23, 2019 7:29 pm did you upgrade the firmware to the latest version on the one that had issues?

Unfortunately I sent it back before I had the chance.

I realized that difference after I posted about it.

So you were able to fix it?


The new EM7455 came in, repeated everything exactly as before but was successful and QMI is running beautifully. I wonder if the previous modem was damaged/corrupted in some way? Well it's been sent back. I wonder ...

swwifty wrote: Sat Jul 20, 2019 6:02 am I realized that difference after I posted about it.

So you were able to fix it?

Unfortunately not. I ordered another module to see if results are similar.

swwifty wrote: Fri Jul 19, 2019 8:42 am Thread here: http://wirelessjoint.com/viewtopic.php?f=17&t=450&sid=e370a379743d0fb0564136c290c4dc2c

I used the command for EM/MC7455 which is at!usbcomp=1,1,10d and had the exact issue you did, but my modem is a EM7455 Not a EM7565.

Well unfortunately that did not fix it. The reset put it back into a oem state which was for a dell laptop and I was unable to get a connection. Reran Daniel's script. Connected fine on MBIM, tried to switch to QMI and no luck, it isn't connecting. Any ideas anyone?

I found a solution if anyone ever gets stuck in my position. I ran these commands.

at!entercnd="A710"
at!RMARESET=1
at!reset

And it defaulted to MBIM,but running the commands for qmi again were successful after the reset.

This is what my router is seeing.
[ 2403.842821] usb 1-1: new high-speed USB device number 5 using xhci-mtk
[ 2404.023418] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2404.030558] usb 1-1: config 1 has no interface number 1
[ 2404.041272] qcserial 1-1:1.0: Qualcomm USB modem ...

So I have a EM7455 in a usb enclosure and I used Daniel Wood to flash it to generic with no issues. After using it for a while I noticed the latency was high so I followed this to switch it over to QMI. https://wirelessjoint.com/viewtopic.php?f=21&t=334
It work for a solid week with no problems but ...

JimHelms wrote: Thu Jul 11, 2019 7:09 am The LED's are assigned and controlled by the router firmware (i.e., GoldenOrb).

You should have a LED Configuration tab under the SYSTEM menu, though I have never messed with them.

I've poked around, but It seems that I can only control 2 LEDs but nothing changes.

There is a picture of the main board on wikidevi.com that labels the LEDs as PWR-5.8G-2.4G-WAN-LAN4-LAN3-LAN2-LAN1. The picture appears to be Version 00, so not sure how the V5 would differ. On the WE1326 that I have, the three from the left are on always on.


Wow, that's odd. For me the 5.8G ...

I know this is a odd question to ask, but the LEDS are unlabeled, I know 5 on the right are WAN/LAN and the power is on the far left but, that leaves two. And the one next to wan is constantly blinking, im assuming that is wifi, what is the one in between power and wifi?, I've never seen it on ...

It is most likely one of two reasons.

1. The wrong firmware version was used. There is a WE1326 and a WE1326V5. One will not work on the other. If you purchased from The Wireless Haven, you need the V5 version.

2. The Save Settings was checked. It must be unchecked when updating the firmware ...

my WE1326 has become unresponsive after updating it with the wifix firmware. only the Power LED is on and the corresponding port when plugged in but im unable to access what can I do?