Help recovering MR1100 boot loop issue

[mosasha]

Hi all and good day,

I have a mr1100 eus version that had a problem which is the device freezes when adding apn so i tried to update the firmware with fdt and the device never booted again i tried every firmware available and nothing fixed the boot loop
so kindly do any one here have a way to fix the issue it will be much appreciated

thanks in advance and best regards

[Rich Hathaway]

In this case it needs to be re-loaded from emergency (9008) mode, this will recover it.

[mosasha]

In this case it needs to be re-loaded from emergency (9008) mode, this will recover it.

thanks for the replay,

sorry to trouble you out but can you please provide more info on how to get the device to this mode and what firmware to use


thanks in advance

[Rich Hathaway]

Hold power while you are plugging it in and keep holding power until your pc dings, about 5 seconds, you will need a patched loader and firmware other than a .spk
Send the loader then erase your device back to 0 then it can be loaded with this type of image (byte by byte) when finished your device will be working again.

[mosasha]

Hold power while you are plugging it in and keep holding power until your pc dings, about 5 seconds, you will need a patched loader and firmware other than a .spk
Send the loader then erase your device back to 0 then it can be loaded with this type of image (byte by byte) when finished your device will be working again.

thanks for the explanation

but this image you mentioned above how to get it..is it available to download?

[Rich Hathaway]

I am not aware of any downloads for it, you never know though, there are prob only a few people that have been able to make firmware like this, netgear never released any or had any leaked that I am aware of and the people that are able to make it dont post it for public, they tend to like to sell services to repair/recover devices for people.
If you search for it it will be a large file, mine ended up being more than a half a gig each as you can see below.

M1_My_Firm.PNG

[mosasha]

I am not aware of any downloads for it, you never know though, there are prob only a few people that have been able to make firmware like this, netgear never released any or had any leaked that I am aware of and the people that are able to make it dont post it for public, they tend to like to sell services to repair/recover devies for people.
If you search for it it will be a large file, mine ended up being more than a half a gig each as you can see below.

M1_My_Firm.PNG

thanks Rich
if its possible for you can you in any way share the firmware to recover the device or if you offer repair services

it will be highly appreciated

Thanks again

[Rich Hathaway]

Threads are not the place to solicit services, the powers that be do like that.
Use the marketplace section of the forum
viewtopic.php?t=2696

[Klaus4]

Hi!! I am not able to run the FDT cause it says no sdk file. Does anyone have one? for me or how can i Create one?

thanks

Klaus

PS I have an ATT device and live in Austria. I have an identical EU router so is there any solution to get the FW out of my EU router and puti in the ATT?

[Rich Hathaway]

I think you mean spk, if you do they are on the web if you look they are not hard to find.
to answer your other question there are no AT&T spk's released or leaked, the only way to get AT&T on your device is to pull the AT&T firmware from a working device and make it reloadable then you would need a proper loader to load it to your device.

[Klaus4]

I will try to put in the EU version in a boot loop ATT. How can I make a backup from my EU version. for flashin in the ATT

[Rich Hathaway]

FDT is an executable that is called up by the command line, I am not sure what sdk you are trying to use but all you need to use it is a command prompt. you can call it up and see its usage by
fdt -h
To make a backup you cannot use fdt to make it or to load it to another device, you would need a working loader (ENPRG/NPRG)

[Klaus4]

do you have link for the Fdt?

Thanks

[Rich Hathaway]

It is all over the web, google for it.

[Klaus4]

I fixed it. It still have ATT Firmware in it but I hope that it will work in the EU

Thanks

[jericsmith]

I fixed it. It still have ATT Firmware in it but I hope that it will work in the EU

Thanks

Could you share what you did to fix it? Thanks!

[Klaus4]

Could you share what you did to fix it? Thanks!

viewtopic.php?p=26543#p26543https://wir ... 543#p26543