Wireless Joint

So, I was needing the 2.4GHz to work and reflashed the device. It was originally showing both 2.4 and 5 GHz broadcasting. Once I rebooted the device now I only have 2.4GHz. This helps me a little bit, but why can't I keep both broadcasting??

Anybody had this issue and resolved it?

I want to first thank the Wireless Joint team for getting my router up and running! The support has been phenomenal.

Sadly, I am back with one (hopefully elementary) questions. My NEXP1GO is broadcasting 5GHz with no issues whatsoever, but my 2.4 GHz isn't...

Under wireless radio0 - MediaTek ...

PS State: Not Attached
RRC: Idle

Both basically say the network is blocking you. You might want to request a new SIM and put it in the new router when you get it.

Or you may want to try to match the modems imei to the hotspot, just in case.


How do I match the IMEI? Is it an AT command or is ...

SIM ICCID is identified. Under the General Information the Sierra EM7565 is still listed as Modem1, but under Provider: it always stays "connecting."

I am not running any TTL rules, would you suggest implementing any? if so, what would they be?

I am connected to the router via ethernet and a Zyxel ...

On the contrary, I still am not connected. I feel like I’m missing something extremely simple from finishing the setup… any ideas?

I ran the command before realizing you were referring to Aweeka, but since I have the info I figured I'd post :D .

AT!GSTATUS?
!GSTATUS:
Current Time: 94 Temperature: 33
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Not attached
LTE band: B66 LTE bw: 20 MHz
LTE Rx chan: 0 LTE Tx chan ...

I found the setting to enable LTE only and turned it on. I'm starting to really need this router to connect, so I'm going to dump a bunch of items from the DEBUG. Hopefully someone can point out the missing piece - At some point it says "SIM Failure" but is still reading the ICCID.

DEBUG Info on ...

Thanks for diagnosing. Do you know the command to change?

AT!BAND?
Index, Name
00, All bands

OK

AT!SELRAT?
!SELRAT: 00, Automatic


OK

AT!CUSTOM?
!CUSTOM:
GPSENABLE 0x01
GPSLPM 0x01
IPV6ENABLE 0x01
UIM2ENABLE 0x01
SIMLPM 0x01
USBSERIALENABLE 0x01
SINGLEAPNSWITCH 0x01


OK

AT!GSTATUS?
!GSTATUS:
Current Time: 13541 Temperature: 33
Reset Counter ...

AT!USBCOMP?
Config Index: 1
Config Type: 3 (Generic)
Interface bitmask: 00001009 (diag,modem,mbim)

OK

I got the results from AT!USBCOMP? after running the other command first! Here are the results.

I have a Franklin T9 from Calyx. When it’s operating it connects to the fast.t-mobile.com APN.

AT!USBCOMP?
ERROR

Still getting errors... I double-checked that my drivers were up to date too. I looked up my device manager and have a device called WD SES Device USB Device that states "no compatible drivers" may not even be related, but I'm really needing this device to connect soon!

Not sure if its an issue but I ran through some of the AT commands again and one seemed to have a duplicate on the:AT+CGDCONT?

AT+CGDCONT?
+CGDCONT: 1,"IPV4V6","fast.t-mobile.com","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
+CGDCONT: 2,"IP","otasn","0.0.0.0",0,0,0,0
+CGDCONT: 3,"IPV4V6","fast.t ...

Not a problem! Best of luck to both us.

Here is my output:
AT+USBCOMP?
ERROR

Maybe my fix is something with this config?

I've entered both of the AT commands above receiving "OK." I still am unable to receive connectivity. Are there any other troubleshooting steps I can take whether it be AT commands or hardware?

I can always revert back to the T9, but would love to use the functionality of the WG3626 Router. I ...

Yes.

AT+CGDCONT?
+CGDCONT: 1,"IPV4V6","fast.t-mobile.com","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0

OK

I've also tried the r.ispn. I feel like I'm missing something fairly elementary, but can't figure it out...

I am using the Calyx Institute plan. I thought it was originally a Sprint program, but when looking in the browser of the T9 with the SIM I noticed it was on the fast.t-mobile.com. I asked The Wireless Haven before purchasing and they thought that it should work. Is it possible to "flash" the IMEI ...

I now know what Mike829 is saying.

I am now back to the original router firmware and have the modem set to "Generic" but I still am not getting internet connection. I also synched the time again.

AT!IMPREF?
!IMPREF:
preferred fw version: 01.07.02.00
preferred carrier name: GENERIC
preferred ...

So, I’ve from the Chinese recovery screen I uploaded a .bin firmware and am now showing MediaTek OpenWrt.

Seeing how I was just wanting to go from telestra to generic, I feel like this is a completely different platform.

Do you mind pointing me to the firmware download that I can enter?

Awesome! Once I get home I'll run these commands and let you know the results. One the firmware is switched to generic should the connection auto-connect?

Thanks again for the support.

So, I may have royally screwed up.

I found a thread on downloading the Generic firmware and most recent drivers. Once drivers were installed I reset the PC and then ran the firmware .exe.

It didn’t seem to be doing anything, so me and my infinite wisdom went into the route - under flash firmware ...

Once I saw that I kind of figured.

Silly question, but is the actual firmware called "Generic" or the firmware is generic to this hardware?

The first two commands seemed to work fine.

See below for the following two outputs:
AT!IMPREF?
!IMPREF:
preferred fw version: 01.11.00.00
preferred carrier name: TELSTRA
preferred config name: TELSTRA_002.007_000
preferred subpri index: 000
current fw version: 01.11.00.00
current carrier ...

Yes the SIM ICCID number is present.

Hey all new to the board, so I apologize If I'm just revisiting old topics. I am also not the most tech savvy so forgive me if I use the wrong terminology.

I purchased the complete router bundle with the above mentioned NEXP1GO and EM7565 Modem. I followed several of the guides on putting the ...