Wireless Joint

This does not look right. Anyone know how I can fix this?

At+CGDCONT?
+CGDCONT: 1,"IPV4V6","vzwinternet","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
+CGDCONT: 2,"IPV4V6","ims","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0

Having issues with my router, here are the steps I have taken.

Factory reset on modem
Firware updated to lates version on Haven Tech Website
Updated APN to tracfone.vzwentp
ran commands posted by Didneywhorl above

Still not able to connect.

Do I need to update TTL?

Thanks in advance.

Didneywhorl wrote: Mon Aug 15, 2022 1:54 pm Then run...
Code: Select all
AT+QCFG="USBNET",2
then
Code: Select all
AT+CFUN=1,1
then reboot the router.

Looks like that fixed the issue. thanks for your help!

What is the firmware version on each modem? Do they match? ( AT+QGMR gets the full fw version)

Are you using the Auto APN features the same on both?

Post each of these from both modems, noted which is which:

AT+QGMR

AT+QBMCFG="List"

AT+CGDCONT?

AT+QCFG="USBNET"

Also:

AT+EGMR=0,7 (Don't ...

Only have the modem that does not work with me. The other is up at our weekend property. Let me get back to you on this.

Hello,

Have a NEXQ6GO set up for Page Plus with the following updates:

Updated APN, and verified that IMEI is compatible with Page Plus service. With these settings the unit I have is working as it should. My sister was impressed with the unit and asked if I could get one set up for her as well ...

Anyone have a guide on what needs to be updated to get PagePlus working on NEXQ6GO? I have visible working and it should work for 90% of my needs, but would also like a backup in case Visible shuts down.

I am assuming APN, but not sure what that needs to be?
Custom Commands entered for Visible, do ...

Didneywhorl wrote: Thu Mar 10, 2022 8:28 am Look into US Mobile.

Most any non-hotspot plan will require identity changes.

After Identity change, what do you recommend?

Thinking Page Plus or Visible.

I am fine with the Data caps 250GB as long as I have some decent speed 10-20.

This would be in a remote area, and per Verizon's site it says we are not eligible for home internet. That would be ideal if I could just use that. I think they even have antennas that they can install if needed.

As far ...

I currently have a NEXQ6GO router and have been successful with getting to work with Visible, but need something that has a bit more speed even if I have a data cap. I am also willing to pay for verizon service, but sounds like this device may not be compatible. Does someone know if I can use ...

gscheb wrote: Fri Oct 22, 2021 7:03 am Turn custom TTL setting off. When you use the custom rules then you don't use custom ttl at all. Try that and see if that changes anything.

That was it. Thank you!

Won't say TTL will say custom rules. When you paste that in there it will change TTL.

Also for good measure copy and past this shown below in to custom rules
Tab to the left of custom TTL settings called custom rules.

#start TTL rules
iptables -t mangle -I POSTROUTING -o wwan0 -j TTL --ttl-set ...

Didneywhorl wrote: Thu Oct 14, 2021 10:41 am Ill look through your logs when I get a min to sit down at my pc.

thank you!

Post the logs here if you have them. A text file attachment works, or just quote the text in full. Maybe the Kernel log too.

Here is the debug information. Sytem Logs and Kernel Logs attached.

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1

B: Alloc= 0/800 us ( 0%), #Int= 0 ...

Didneywhorl wrote: Wed Oct 13, 2021 10:21 am Does the modem show up on the debug screen (bottom part) or in the system log?

No mention of router under Debug information. The system log has several references to modem, but not really sure what I am looking for.

Not sure if I should post this here or under the modem section, but having an issue with my router where after booting up, I get a message that there is no modem present.

After emailing with one of the admins at The Wireless Haven, they advised that I should upgrade to latest firmware without ...

For now don't connect anything to the router except the modem and restart the system.

Does the modem have a microUSB connector?

An actual set of pictures would help us understand the details.

Its the NEXQ6GO-U sold by The Wireless Haven. Basically purchased about 2 months ago, so fairly new ...

The modem connects within 2 minutes of your bootup:

[ 88.560547] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB3

… it then diconnects within 6 minutes:

[ 345.806966] usb 1-1.3: USB disconnect, device number 8
[ 345.812814] option1 ttyUSB0: GSM modem (1-port) converter now ...

[ 0.000000] Linux version 4.9.211 (dairyman@Compaq6300) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7976-ca47026b7d) ) #0 Wed Jan 29 16:06:05 2020
[ 0.000000] MyLoader: sysp=fff7ffff, boardp=ffffffff, parts=ffffffff
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS ...

think I found it.

Has anyone received this in the Network status page?

For anyone looking for a flat panel option, this unit worked just as well as the Poynting Xpol at half the cost. the only downside is cables are pre installed and only 6ft long. Cable rating is LMR 200 equivalent per manufacturer. As mentioned Performance is identical to Poynting XPOL the difference ...

The parabolic antenna can be tricky, the size is misleading, you would think it’s a large net to catch a signal with. But in fact it’s more like a laser pointer. Getting on the signal and staying on the signal is not easy.

The problem with putting your antenna higher is you need more cable ...

I wouldn't say 35+% increase in gain is real similar ( 11 dBi x 1.3636 = ~15 dBi ), but I get what you mean. It's not astronomical.

For about $20 more (Not including shipping charges, The Wireless Haven is free shipping over $100) and to give up 35% increase in gain, your saying the aesthetics ...

Landmasses blocking LOS will be a problem no matter what you use, but it sounds like your fresnel is blocked more than the dead LoS. You might do best with a higher dBi panel. Some would say a parabolic with real high power would be even better, but I'm not entirely sure they work well in non-LoS ...

We have our setup working and there are two main places we plan on using, Duck Creek Village in Utah and Bartlett Lake in AZ. The first seems to be dialed in with a reliable signal and decent download speed, but barely able to get a signal at Bartlett with very low data speeds 3mbps down.

The tower ...

dbshelton wrote: Thu Aug 26, 2021 7:36 am How can I know if I am testing my phone's cell internet connection or the Wifi connection on speed testing?

Turn the phone on airplane mode, then only turn on Wifi.

From what I seen on tethered phone set up it takes a TTL 66 or higher along with VPN. Been just using 88 just because. But haven't tried on a modem yet though. Need someone to test that out please. Try this below and put VPN on client device. (item using wifi)
Like said before free warp cloudflare ...

Adm1jtg wrote: Tue Aug 24, 2021 6:34 pm I would think the panel with 2 inputs simply has 2 elements inside it. Like 2 antennas in one enclosure.

Agree, I was really more interested in the db ratings. Sounds like there is no gain to be had by going with the individual units.

Question on flat panels. I noticed The Wireless Haven sells Flat Panels where the antenna is single configuration which can be mounted in MIMO x polarity installation, the the one below.

https://thewirelesshaven.com/shop/antennas/cellular-antennas/directional-panel/700-2700mhz-15dbi-4g-lte ...

Which modem are you using?

My EM12s reports its antenna inputs as: first value is the primary, second is the differential
AT+QRSRP
+QRSRP: -99,-103,-140,-140

The EM7544 as: RxM is the primary, RxD is the differential
AT!GSTATUS?
PCC RxM RSSI: -82 RSRP (dBm): -112
PCC RxD RSSI: -82 RSRP (dBm ...

It takes two to do MIMO as in the tower must also play nice. The problem is when you are out in the Country the towers are not always the best or have the latest technology.

Just guessing.

Take your setup on a road trip to other towers.

https://thewirelesshaven.com/shop/power-adapter/12vdc ...

Have my NEXQ6GO router setup and looking to verify that everything is working as expected. Have decent signals using paddle antenna 90db with 80+signal strength. What I wanted to make sure if is both antennas are working as expected. My expectation is that I would if I disconnect one antenna the ...

Will have to give it a shot. For my purposes, even 5mb on cellphone is ok. Need the download speeds for downloading/uploading larger files for work. Possible even with a 5mb connection, but slow.

I am being throttled on my visible tethered phone. But haven't tried one in router since this started. So don't know if it is happening there too. Did you put this and do nothing with the Custom ttl change?

Also changed custom TTL to 64. Seems like a reboot solves the throttle issue for some ...

Won't say TTL will say custom rules. When you paste that in there it will change TTL.

Also for good measure copy and past this shown below in to custom rules
Tab to the left of custom TTL settings called custom rules.

#start TTL rules
iptables -t mangle -I POSTROUTING -o wwan0 -j TTL --ttl-set ...

gscheb wrote: Fri Aug 20, 2021 6:29 pm Look at this one just for TTL
https://wirelessjoint.com/viewtopic.php?f=32 ... 630#p18630

Thank you again. Which tab do I find the TTL/Custom rules that are in the link you provided?

Thank you!

Not sure if this helps anyone, but with my new setup. If I run a speedtest, getting throttled. Plug into my work laptop, where everything is routed through a VPN and no issues. I think that is what you were saying above, but either way that works well for my use case as that will be most of my use ...

Just got my NEXQ6GO router and Quactel EP06 modem set up and followed configuration detailed below.

https://wirelessjoint.com/viewtopic.php?f=16&t=2212

Couple questions:

on my router I had 6 cgdcont to replace, is that normal?

Also did not see where I would update TTL.

connected, but throttled.

Just installed this in my router and not sure which ports to use, there are two grouped right next to one another, assuming those would be the cellular and the one by itself is GPS?

got it, thanks.

Thank you. I just realized my tmobile phone is unlocked and had no issue. Is this a deal where I have to keep the phone I activate it with unused?

Hello,

new to the forum and looking at a router build using NEXQ6GO router for use in our Trailer. Has anyone wired this or a similar router using power directly from a 12v battery (Lifepo4 in this case). I know the voltages can fluctuate from 12-14.2 using my charge profile, was not sure if that ...

Hi,

new to this form and feel like I have a lot to learn. Planning on doing a build using NEXQ6GO router along with guides found on this forum, planning on using with a Visible Sim. Feel like I could get through it based on the guides on this form.

Question relates to activating a Visible sim card ...

Search found 45 matches