Wireless Joint

Hmmm... found a thread about making the modem 'GENERIC' rather than visible. Re-ran that. Switched back to port 64 and seem to be up and running again.

Hi. I thought all this was up and running, but it only worked for a very short time and I have been out of town and haven't been able to follow up.

Router: NEXR5GO
Modem: EM7565

The best I can tell, I followed all the directions provided with the router. Since it isn't working, I have been trying ...

Does anyone know how to setup load balancing on the NEXR5GO so that:

1) The modem is used (primary)
2) As a failover, it will use the WiFi Hotspot

Thank you

I believe these were my problems along the way:

I had initially followed the instructions correct; however, I did not have the extra custom TTL Rules in there. When I did put them in there, I replaced what was already in there instead of adding to it, so I was still down.

Then, in trying to ...

I am up and running! Thank you all so much for your help!

Found this on another thread

AT+QMBNCFG="List"

... will give it a try if I can get my modem connected again.

Didneywhorl,

Hello. Regarding the antenna question, thank you. I understand your concern there. I already had the appropriate antennas. Thanks for checking though.
On the firmware image, I will have to check into that. I paid extra to have 'generic firmware', so I assume it would be the active ...

The modem came with the generic firmware.

I may have identified the issue. Now, the system says "No Modem". (Note... this new error occurred before I saw the message about IP6).

I checked connections and re-seated the cards, but that did not fix the issue.

Am I right in thinking this has been a flaky modem problem and it has just ...

Any other ideas I can try this weekend?

Thank you.

They are round and about 8 inches tall. I don't think it is an antenna issue because with my phone I get a strong signal (4-5 bars usually)... and the system doesn't show a weak signal... the signal shows dashes because it is not connected at all.

.... and... the signal was fine before the reboot ...

Tried each of the IP4 and IPV6 with 64 and 65. Also tried a PagePlus sim card.

Since it is not connecting, I can see no signal levels.

I agree with your conclusion that it is not connecting.

I tried the custom rules settings described above. I also tried these:

iptables -t mangle -I POSTROUTING -o wwan0 -j TTL --ttl-set 65
iptables -t mangle -I PREROUTING -i wwan0 -j TTL --ttl-set 65
ip6tables -t mangle -A POSTROUTING -o wwan0 -j ...

AT!GSTATUS?
!GSTATUS:
Current Time: 568 Temperature: 36
Reset Counter: 1 Mode: ONLINE
System mode: WCDMA PS state: Not attached
WCDMA band: WCDMA 1900
WCDMA channel: 562
GMM (PS) state:DEREGISTERED ATTEMPTING ATT
MM (CS) state: IDLE UPDATING

WCDMA L1 state:L1M_PCH_SLEEP LAC: 0381 (897)
RRC ...

After rebooting (unplugging and plugging back in), it is working like it did before I swapped the position of the SIM card. ie. says "Connecting", but there is no signal information.

I changed the SIM card location and it is now connecting; however, it is so slow that fast.com only shows 0, and speedtest.net can't even load. googling "test" took over 10 seconds to get a reply.

As a point of clarification, I put my sim card in the adapter for the modem. There is, however, a sim card adapter on the motherboard as well. Should my SIM card have gone there?

Issuing a GSTATUS? command I get:

!GSTATUS:
Current Time: 122 Temperature: 29
Reset Counter: 2 Mode: ONLINE
System mode: WCDMA PS state: Not attached
WCDMA band: WCDMA 1900
WCDMA channel: 9731
GMM (PS) state:DEREGISTERED LIMITED SERVICE
MM (CS) state: IDLE LIMITED SERVICE

WCDMA L1 state:L1M ...

Thank you all for replying. All of that is done now. However, I am still getting the same thing. If I go to Network Status I see the following:

GENERAL INFORMATION:
Modem: sees my Sierra modem
Provider: Connecting
Comm Port: /dev/ttyUSB1

MOD/SIM
Show all my info
SIM Name: Line 1

SIGNAL ...

Well, the hardware was fairly simple to put together (except for a missing screw to hold the modem into the adapter).

I turned on the NEXR5GO, got logged in and it appears to see my modem, sim card, and phone number. However, the connectivity section was blank. I don't know if this means it is not ...

Hi. I bought a WE826-T2 via ebay and discovered it had no ability to set the MCC or MNC so I can't get my SIM card online.

Then I discovered this website, but I can't seem to get any firmware to load. Every time I attempt it, I get the message 'Invalid Version'.

Currently the firmware that is on ...