Wireless Joint

I am upgrading from a cat6 to a cat12 modem. This is a Quectel EP06-A with the Wireless Joint upgraded firmware.

$50 plus shipping.

Been connected for a few days now. It looks like my connection is solid. Thank you all for the help.

Thanks for the information!
I was moving from PagePlus to TMobile... It looks like everything got updated.

AT+QMBNCFG showed one active...

AT+QMBNCFG="List"
+QMBNCFG: "List",0,1,1,"ROW_Generic_3GPP_PTCRB_GCF",0x0801FE02,201910231


After the reboot
AT+CGDCONT?
+CGDCONT: 1,"IPV4V6","fast.t ...

The following command always produces an error. Probably because it is in use, is there a way to disable it?
AT+CGDCONT=1
The rest of the commands work without error
AT+CGDCONT=2;+CGDCONT=3;+CGDCONT=4;+CGDCONT=5;+CGDCONT=6;+CGDCONT=7;+CGDCONT=8;+CGDCONT=9;+CGDCONT=10;+CFUN=0;+CFUN=1 (set all ...

Thanks for that
I am looking for what commands are required after a fresh start (oem state).

In the txt doc provided above, the IPV Modes section looks carrier specific.
Do I run all the commands starting with ...Set Connection Modes?

I am open to PagePlus (preferred) or SimpleMobile. I have all the router settings I need for those. What I am not sure about is what modem (at+commands) settings are needed to be addresses from a factory reset (for the Em-12g).

@kzaudio @gsheb...
Were either of you able to get your EM-12Gs set up? I am moving from the EP06 to the EM-12. Currently I am able to connect but my speeds are slow. Can you share a set of at commands you used to get your devices running? I looked at the commands from the previous post, but those ...

Hey All,
I just activated my sim card on PagePlus. It shows I have one payment history and no phone. That said, my phone is able to make calls and connect to cellular. Is that correct? What should the dashboard pages look like of my PP account?

Great writeup...

The following command always returns an error on the EM12. The rest of the contexts are fine, but #1 always returns an error.
AT+CGDCONT=1

Were any of you able to run this command?

@didneywhorl
Thank you very much, the additional doc adds clarity. I think I have enough understanding to start issuing AT commands... fingers crossed I have a working modem on the other side.

Would you look at that, there it is... Thank you.

I am looking at Page Plus (verizon).
I have an iPhone 6s that is willing to donate its IMEI and MAC address if needed.

When I set out to get a cellular router up and running, I had no idea what I was getting into. Now I am getting clarity on the process and the rabbit hole keeps going (and going and going). Today an new detail reared its ugly head. The issue of the IMEI number. I thought the IMEI came with the SIM ...

@Didneywhorl
Thank you for the tip. The other post makes sense. To be clear, in order to get the "Deactivate" command to work, we need to set it, then toggle QMI to MBIM then back to QMI? With lots of modem reboots in between all the commands?

Hey All,
I have a EP06 setup and am trying to get a EM12g working. Looking at the EP06 AT commands and the Quectel manual ( https://www.quectel.com/UploadImage/Downlad/Quectel_EM12&EG12&EG18_AT_Commands_Manual_V1.0.pdf ), some commands are not found :| . Specifically the commands below.


AT ...

Does anyone have the EM12g working?
Can you share a list of the required AT commands?

@BillA,
Thanks for the info! You mentioned auto-scan, that seems a lot easier than using the specific band commands. The spreadsheet came up with the following commands:

Band 2 = AT+QCFG="band",0,2
Band 4 = AT+QCFG="band",0,8
Band 5 = AT+QCFG="band",0,10
Band 13 = AT+QCFG="band",0,1000
Band 66 ...

Is there a list of all the AT commands needed to set up the EM12g? I am looking to set up a EM12 on PagePlus.
I looked at the spreadsheet posted above and decided quickly that I was in over my head. I do not want to brick the modem.

Aside from the full list of commands, which bands are required ...

Thanks for the info!
I will check out those options. I went with the NEXR5GO router and an EP06 modem.

Hey All,
It has been a long road but I finally have my router installed in the van and am ready to get a service plan. I was planning on Verizon, but the threads in here about the 5mbps limits on Verizon have me a little worried. I have a Verizon and an ATT sim. Can you please suggest one carrier ...

Is it possible to edit the outbound packet data going through a router running OpenWrt? My router is in the mail and I am coming up to speed on all this.