Wireless Joint

This is super frustrating. I've built lots of pc's but I've yet to find any instructions or anything for this device. Without device support, even resetting it took research. Is there any video/manual/guide to the 1608 that you know of? Thanks for your response.



As far as I know, none of the ...

How do you flash a router that you can not access. It does not show up via WiFi or Ethernet. Tried the reset of holding the reset button then applying power. I get a red light and a flashing WiFi light. After I release the reset button there is a delay then the USB light comes on. and the WiFi ...

this is how I did it:

1. Command: AT!ENTERCND="A710"

2. here I want to which image is the modem using: Command: AT!IMPREF?
AT!IMPREF?
!IMPREF:
preferred fw version: 01.08.04.00
preferred carrier name: SIERRA
preferred config name: SIERRA_002.001_000
current fw version: 01.08.04.00
current ...

Hi all. I just recently purchased an EM7565 from a friend to upgrade from my EM7455. Running an AT!IMAGE?, it shows that there's a newer firmware version installed in slot 1, but I can't for the life of me figure out how to switch over to that firmware.

AT!IMAGE?
TYPE SLOT STATUS LRU FAILURES ...

.
.
Here's more info about the new ZBT WG1608 5G-ready router, and a list of 5G modems at the end of this post.

In a nutshell, it's a souped up WG3526, while running on the same MT7621 chip, it comes with a new 2G/5G WiFi chipset and other interesting upgrades.
It can work with both 4G-LTE and 5G ...

Hello

I wanted to purchase an EM160R card which is a 4x4 MIMO modem. But currently I still only have a 2x2 antenna which I may upgrade later.

https://i.imgur.com/Db40Xz5.png

I have the following questions:

Q1 : In case of a 2x2 MIMO antenna, on which ports should I connect the 2 cables? One ...

As some of you may know, or have recently found out, the newest Quectel modems (EM160, EM120, RM500, RM510, RM502) do NOT use all of the same AT commands as the predecessor modems.

Here are a list of a few new commands and what they should do, and a list of commands that I've found not working ...

The change does survive reboots. To get your pre-changed values, run these commands, one at a time:

at!entercnd="A710"
at!usbcomp?

usbcomp is a password protected command, hence the need to supply the default password of "A710" first. They are protecting you from shooting yourself in the foot. If ...

I have the same router/modem---new to me (rig)
trying to get up with a Verizon tablet plan-post paid, that I know works in another router--no love.
I got this info over on the FB site, and it worked for me. run each command and wait for an (ok) on last command, wait--it should reboot on it's own ...

I have the same router/modem---new to me (rig)
trying to get up with a Verizon tablet plan-post paid, that I know works in another router--no love.
I got this info over on the FB site, and it worked for me. run each command and wait for an (ok) on last command, wait--it should reboot on it's own ...

This tutorial will demonstrate a fairly easy way to restore the Sierra Wireless modem COM port using a Windows machine.

This process is used ONLY when a modem is stuck in QDLoader Mode. This work around will not work when one has lost their modem port by using the wrong AT Commands to change its ...

What you're going to find is that Golden Orb ("GO") and therefore The Wireless Haven firmware based on it are much more user friendly firmware(s) that has many things self-configured and therefore you don't need a degree is rocket science to utilize it, and the opposite end of the spectrum is the ...

And it works with ps4? My only problem is connect to PlayStation network.



Most mobile carriers provide a "private IP" address instead of a public one which is required for some gaming consoles.
Check out the posts below for some possible solutions:

https://support.xbox.com/en-US/help/hardware ...

Finally got it working and stable. Disney plus, Prime and Netflix all working. Speeds are still pretty slow, but I'm in a highly congested area. Will try a speed test later tonight.

This is a game changer for anyone who relies on LTE for their primary connection. Will be making a donation once ...

This tutorial will demonstrate the build and configuration process for the M2M NEXG H721 Dual Modem Router.

UPDATE 2020: There are numerous versions of the M2M Dual-Q H721 (and under other private labeling/branding) Dual Sim 5G 4G Dual Modem routers being sold that are defective. There is no ...

I have a new Quectel EM160R-GL for sale. It is still sealed in the OEM package.
It is a production model so I assume it has the latest firmware on it. I wanted to leave the package sealed, so I did not check it.

Let me know if you are interested.
Regards,
RJ

Awesome, I'll do some research. Thank you!



The preferred method for tethering a phone to a router is via a USB cable, which is faster than WiFi and also charges the phone at the same time. It's actually quite simple to do it on a router which has a USB port and is flashable with OpenWRT ...

shrecewa wrote: Thu Oct 07, 2021 8:58 am

Yep

https://www.t-mobile.com/isp