Wireless Joint

Got it all hooked up working like it suppose to with Verizon.

Off Topic, but do you have any links to info on how to setup modem manager with stock openwrt? I want to replace GoldenOrb with openwrt, so I can have ip pass through.

I just built it using these three pages:
https://openwrt.org/docs/guide-developer/build-system/use-buildsystem
https://openwrt ...

Thanks for the info. I'm going to set it up soon, and do a full write up on how to do this.

UPDATED 12-20-2022: The system files on the new kernels of OpenWRT/GoldenOrb/ROOter are continuously changing.

The splash screen in the attachment below was designed and used for our WiFiX routers a build or two back.

Instructions are included in the file and is shared for personal use only ...

This tutorial assumes:

1. The modem has been installed in the router.

2. WiFiX/GoldenOrb firmware is loaded on the router.

STEP THREE: CONFIGURING THE ROUTER AND MODEM

Log in the router's user interface at 192.168.1.1

NOTE: It may be necessary to clear the browser cache if any issue is ...

IPv6 works fine with QMI on both Sprint and Verizon.

Tested on:
1) GO 3-10
2) OpenWRT w/MM
3) Arch w/MM
Verizon was on the EM7565 (FW12) for all 3. Sprint was on the EM7455 (FW23) for all 3.

An interesting note is that ipv4 might actually be handled differently on verizon - I had mentioned ...

I'm probably going to get one of those AC measuring devices, as I need one anyways. I'll take some measurements of the PI with a few modems and see what happens.

There is a picture of the main board on wikidevi.com that labels the LEDs as PWR-5.8G-2.4G-WAN-LAN4-LAN3-LAN2-LAN1. The picture appears to be Version 00, so not sure how the V5 would differ. On the WE1326 that I have, the three from the left are on always on.

I know this is a odd question to ask, but the LEDS are unlabeled, I know 5 on the right are WAN/LAN and the power is on the far left but, that leaves two. And the one next to wan is constantly blinking, im assuming that is wifi, what is the one in between power and wifi?, I've never seen it on ...

Thought I'd start a thread to discuss WISPs. I think a lot of folks that are technical and setting up 4G conections are probably learning about WISPs in the process. They are very common in rural areas now to solve the rural broadband problem.

Part of my adventure into 4G as a home internet ...

xdavidx wrote: Fri Jun 28, 2019 9:57 pm Which takes precedence -- this script or if you set the APN manually through AT commands through the modem->misc screen?

The script will program (or reprogram) the APN on connection.

Twoods196 wrote: Sun Mar 29, 2020 8:46 am Can you provide the link where you login to your prepaid iPad plan? The one I was using is saying this is no longer where you login too. Thanks

I just use the ipadlanding page, which forwards me to:
https://dcp2.att.com/OEPNDClient/

Neither plan will work in a modem due to the IMEI recognition. And as far as the speed of your tablet plan not sure if it’s your signal because with the stay at home orders in certain areas the towers are congested and causing slow speeds.



But didn't you say earlier if you activate the service ...

Hey Bill! Do you have personal experience of blowing through say 600GB on PagePlus over several months and not getting shut down? I'm about to serve my household of 4 and my grandma and my uncle with this service, but I really want to gather data points saying this is going to be fine before doing ...

Unfortunately, I'm down in the "barely 1 bar" territory here. I just put the sim in a Pixel 1 and went on the roof. Handful of mbps down and 0.3 to 0.4 up. My regular phone on a t-mobile sim at least got teens down and 1-2 Mbps up, and it doesn't even support all the bands. The pixel 1 may only be ...

I'm in the same boat as you xdavidx, I too have att tablet/sierra combo and am looking for a backup for safety net reasons. The way I see it is they are cracking down on the data hog abusers as of now, when they see non legit sim they suspend the account. I'm pretty sure if you keep your numbers ...

Put the sim card into a phone, call customer service from another phone (800-331-0500 or 800-901-9878), tell them that it has stopped working all of a sudden, and ask them to fix it. Course don't tell them that you're going to use it in a router. If they were able to fix it, do NOT put it back ...

Thanks for posting that. Could come in handy for someone.

Regarding powering the usb enclosure remotely, with one of the extenders that has the extra power jack, that's only needed if you aren't using a powered hub?

Good stuff, if for no other reason, than it could be done, so it was done. :D ...

shwaba wrote: Wed Apr 01, 2020 9:15 am PagePlus and Simplemobile

PagePlus APN is "tracfone.vzwentp" (without the quotes)
SimpleMobile APN is "simple" (without the quotes)

When going through the T-moble website to purchase the plan, $60 "Simply Prepaid Unlimited Plus", their website is a little goofy and took me a minute to find the bring your own device checkbox to continue. It automatically adds a 3-in-1 SIM Starter Kit. Do I need to be aware of anything else before ...

Hello.
If you do try pageplus please report in and let us know how it does. Very interested in how much it is deprioritized.
Thanks

I hate to bump this thread, but hate even more than that starting a new thread on the same subject! AND I told Bill I will post my findings here

I have some information for you on the ATT PREPAID plans. First:

1- You can change your IMEI with ATT. You can call them and they will change it and ...

So it is not sim/provider related. Just modem related. Multiple cat9-20 modems do not work? Are they all Sierra?


I don't know the exact issue. Just that the Cat6 modem is working with both sims from ATT that are Prepaid.

- $75 plan Working with Cat6
- $65 Plan working with Cat6

None of these ...

I tried using the $65 att plan and it would work in my phone but not in my WE826. I have a CAT6 Modem, to get it to work in the we826 are you just using the apn name like "nxtgenphone" or is there anything else that needs to be setup to make it work? I was able to get a signal, attach an everything ...