Wireless Joint

Not sure what I did....I somehow removed my modem....any help would be appreciated

Thu Jun 27 12:23:45 2019 : Attempting to Connect Modem #1 (Sierra_Wireless,_Incorporated Sierra_Wireless_EM7565_Qualcomm®_Snapdragon™_X16_LTE-A)
Thu Jun 27 12:24:29 2019 : Retry Connection with Modem #1
Thu Jun 27 12:24:40 2019 : Attempting to Connect Modem #1 (Sierra_Wireless,_Incorporated Sierra_Wireless_EM7565_Qualcomm®_Snapdragon™_X16_LTE-A)
Thu Jun 27 12:25:16 2019 : Retry Connection with Modem #1
Thu Jun 27 12:25:27 2019 : Attempting to Connect Modem #1 (Sierra_Wireless,_Incorporated Sierra_Wireless_EM7565_Qualcomm®_Snapdragon™_X16_LTE-A)
Thu Jun 27 12:25:26 2019 : Attempting to Connect Modem #1 (Sierra_Wireless,_Incorporated Sierra_Wireless_EM7565_Qualcomm®_Snapdragon™_X16_LTE-A)
Thu Jun 27 07:31:56 2019 : Attempting to Connect Modem #1 (Sierra_Wireless,_Incorporated Sierra_Wireless_EM7565_Qualcomm®_Snapdragon™_X16_LTE-A)
Thu Jun 27 07:32:41 2019 : Modem #1 Connected
Thu Jun 27 07:39:14 2019 : Disconnect (Removed) Modem #1

I go to 'Modem" and "Debug Information" and all I see is this message:

No entries in log file

This is under the message:

Device Information
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 4.14
S: Manufacturer=Linux 4.14.131 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=101c0000.ehci
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
********************************************************************************************************
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=85.37
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
********************************************************************************************************
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=9091 Rev= 0.06
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=Sierra Wireless EM7565 Qualcomm® Snapdragon™ X16 LTE-A
S: SerialNumber=UF92127423021505
C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#=12 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#=12 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#=13 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=
I: If#=13 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=
E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
********************************************************************************************************
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 1
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 4.14
S: Manufacturer=Linux 4.14.131 ohci_hcd
S: Product=Generic Platform OHCI controller
S: SerialNumber=101c1000.ohci
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

Hmmm...not sure what this means...get these messages when I try entering commands


Thu Jun 27 09:32:15 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

Thu Jun 27 09:32:22 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

Thu Jun 27 09:32:51 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

Thu Jun 27 09:33:13 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

Thu Jun 27 09:33:33 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

Thu Jun 27 09:36:05 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

Thu Jun 27 09:36:12 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

Thu Jun 27 09:36:25 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

Thu Jun 27 09:36:43 2019 : /dev/ttyUSB Can't open device /dev/ttyUSB.

I would first try to reset the firmware and configurations. Go to SYSTEM > BACKUP / FLASH FIRMWARE > RESTORE > RESET TO DEFAULTS > PERFORM RESET

When it comes back on line, enter the correct APN, and set the time Zone (and sync with browser). Be sure and SAVE and Apply all changes.

Then, power off, wait a few seconds, and power back on the router.

I would also make sure the EM7565 is seated good and all the way into the Mini PCI-E to M.2 adapter.

tried the RESTORE...Same results...will try reseating the EM7565 tonight.....Hoping this resolves...

to restore the modem COM port, a USB to M.2 (NGFF) adapter or enclosure is required to connect the EM7564 to a USB port on the Windows PC. got one ordered.

Hoping this finally gets me up and running.

ok..finally got the COM port restored. Still having issues connecting.

Good work.

It does show you are connected to the carrier.

But, notice the disparity between the RxM and RxD signal stats. They need to be fairly close to one another. This is the first place to start.
The RxM represents the MAIN antenna connector port on the modem.
The RxD represents the AUX antenna connector port on the modem.
The PCC represents the Primary carrier (Band 66) while the SCC represents the Secondary carrier (Band 13) used for Carrier Aggregation.

When we see this much of a difference, it is usually one of the following:

• The MHF4 connector has popped off the modem AUX port or is grounding out against the metal part of the modem.

• The modem pigtail cable is cut and/or damaged. This can happen when reassembling the cases and getting lodged between the case and LED holes.

• The MFF4 connector is bent or damaged (it does not take much to damage them).

• The MHF4 is connected to the MAIN and GPS modem connector port as opposed to the MAIN and AUX.

• If using External Antennas, a bad cable, connector or moisture in the connectors. This is easy to troubleshoot by swapping the SMA connectors on each side of router, and then see if the RxD swaps readings with the RxM.

I know you guys are closed...so, favor please.

Are these the right jumpers for the EM7565?

https://www.amazon.com/Female-Pigtail-J ... HV6LY?th=1

Nope, those are RP-SMA. You need SMA.