Wireless Joint

Posted: **Thu Mar 04, 2021 9:15 am**

Dear community,
I bought WE826-Q (according to the description it was supposed to be WE826-T, but that's a different story ...)
The router was supposed to have an LTE modem, but in the settings of the original OS router (any proprietary version of OpenWRT?) there was no way to set it up.
So I installed GoldenOrb (2020-07-26). In the Modem section, it shows "No Modem Present".
However, some device appears in Debug Information.

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 4.09
S: Manufacturer=Linux 4.9.211 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=ehci-platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
********************************************************************************************************
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=85.37
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
********************************************************************************************************
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b05 Rev= 2.32
S: Manufacturer=USB Modem
S: Product=USB Modem
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

The router has 2 GSM antennas, 2 Wifi antennas and also a slot for a SIM card.
Can anyone give me some tip on how to run a router with LTE? Any missing driver? Or something else?

I would greatly appreciate any help. Thanks!

Posted: **Fri Mar 05, 2021 11:47 am**

Its showing up there as "USB Modem" which is technically correct, but the details of VID and PID show it to be an off brand modem I cant really find any info for. This may be the issue, driver support.

you can try to set the modem to a ttyUSB2 so that the firmware can connect to the AT command terminal.

Go to the menu: MODEM > CUSTOM MODEM PORTS > CUSTOMIZE and add the following information:

Code: Select all

Switched Vendor ID: 1c9e
Switched Product ID: 9b05
PPP Modem Data Port: /dev/ttyUSB2
Communication Port: /dev/ttyUSB2

If that doesnt work try to add this script at system/startup/Local Startup.

Code: Select all

echo "0x1c9e  0x9b05" > /sys/bus/usb-serial/drivers/option1/new_id

Click submit and reboot router

You getting the Q version versus the T2 is an upgrade.

Posted: **Mon Mar 08, 2021 9:23 am**

Thank you very much for your tips! I will try and let you know.

Posted: **Wed Mar 17, 2021 11:00 am**

Thanks again for your tip. I think we've moved a little. At least in that the modem has already been recognized.
However, there are still connection issues.
After hard restart there are some error messages in the Debug Info:

Tue Mar 9 17:22:34 2021 : /dev/ttyUSB2 AT+CFUN=1
OK
ATI
Manufacturer: Manufacturer
Model: HSPA USB MODEM
Revision: LQAPQ04.1.0_M084
IMEI: 862234020220168
+GCAP: +CGSM
OK
AT+CNUM
ERROR
AT+CPBR=?
ERROR

Tue Mar 9 17:22:36 2021 : /dev/ttyUSB2 AT+CIMI
ERROR

Tue Mar 9 17:22:38 2021 : /dev/ttyUSB2 AT+CRSM=176,12258,0,0,10
+CRSM: 144,0,"982420602223138830F9"
OK

Tue Mar 9 17:22:41 2021 : /dev/ttyUSB2 AT+COPS=3,2;+COPS?
ERROR

Tue Mar 9 17:22:42 2021 : /dev/ttyUSB2 AT+COPS=0
ERROR

Tue Mar 9 17:22:46 2021 : /dev/ttyUSB2 ERROR

Tue Mar 9 17:23:05 2021 : /dev/ttyUSB2 AT+CMGS=?;+CMGL=?;+CMGR=?
ERROR

There are some problems with PIN code because there is an error message in the Network status: Failed to Connect : Pin Locked. Although I'm sure the settings are correct.

I've been playing with AT commands a bit, the answers seem to be fine. But the router is still not connected to the Internet.

Tue Mar 9 17:25:44 2021 : /dev/ttyUSB2 AT+CPIN?
+CPIN: SIM PIN
OK

Tue Mar 9 17:26:12 2021 : /dev/ttyUSB2 AT+CPIN=XXXX
OK

Tue Mar 9 17:26:20 2021 : /dev/ttyUSB2 AT+CPIN?
+CPIN: READY
OK

Tue Mar 9 17:27:07 2021 : /dev/ttyUSB2 AT+CSQ
+CSQ: 24,65
OK

Tue Mar 9 17:27:18 2021 : /dev/ttyUSB2 AT+COPS?
+COPS: 0,0,"O2 - CZ O2-CZ",7
OK

Tue Mar 9 17:27:30 2021 : /dev/ttyUSB2 AT+CGREG?
+CGREG: 0,1
OK

Tue Mar 9 17:27:46 2021 : /dev/ttyUSB2 AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0
+CGDCONT: 2,"IPV4V6","","0.0.0.0",0,0
OK

Tue Mar 9 17:28:04 2021 : /dev/ttyUSB2 AT+CGATT=1
OK

Tue Mar 9 17:28:20 2021 : /dev/ttyUSB2 AT+CGATT?
+CGATT: 1
OK

Tue Mar 9 17:29:06 2021 : /dev/ttyUSB2 AT+CGACT=1,1
OK

Tue Mar 9 17:29:42 2021 : /dev/ttyUSB2 AT+CGPADDR=1
+CGPADDR: 1,100.79.140.132
OK

Tue Mar 9 17:30:14 2021 : /dev/ttyUSB2 AT+CGDCONT?
+CGDCONT: 1,"IP","internet","0.0.0.0",0,0
+CGDCONT: 2,"IPV4V6","","0.0.0.0",0,0
OK

What is insteresting, after the softrestart, the modem responds differently.

OK
ATI
Manufacturer: Manufacturer
Model: HSPA USB MODEM
Revision: LQAPQ04.1.0_M084
IMEI: 862234020220168
+GCAP: +CGSM
OK
AT+CNUM
OK
AT+CPBR=?
+CPBR: (1-250),40,47,2,47,47
OK

Tue Mar 9 17:24:08 2021 : /dev/ttyUSB2 AT+CIMI
230020101549979
OK

Tue Mar 9 17:24:10 2021 : /dev/ttyUSB2 AT+CRSM=176,12258,0,0,10
+CRSM: 144,0,"982420602223138830F9"
OK

Tue Mar 9 17:24:17 2021 : /dev/ttyUSB2 AT+COPS=3,2;+COPS?
+COPS: 0,2,"23002",7
OK

Tue Mar 9 17:24:19 2021 : /dev/ttyUSB2 OK

Tue Mar 9 17:24:21 2021 : /dev/ttyUSB2 AT$QCPDPP=1,1,"","o2"
ERROR

Tue Mar 9 17:24:27 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:28 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:30 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:31 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:33 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:34 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:39 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:42 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:44 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:45 2021 : /dev/ttyUSB2

Tue Mar 9 17:24:59 2021 : /dev/ttyUSB2

Tue Mar 9 17:25:02 2021 : /dev/ttyUSB2 OK

Tue Mar 9 17:25:04 2021 : /dev/ttyUSB2 AT$QCPDPP=1,1,"","o2"
ERROR

Tue Mar 9 17:25:18 2021 : /dev/ttyUSB2

Tue Mar 9 17:25:25 2021 : /dev/ttyUSB2

Tue Mar 9 17:25:27 2021 : /dev/ttyUSB2

Tue Mar 9 17:25:29 2021 : /dev/ttyUSB2

Tue Mar 9 17:25:39 2021 : /dev/ttyUSB2

Tue Mar 9 17:25:46 2021 : /dev/ttyUSB2 OK

Tue Mar 9 17:25:47 2021 : /dev/ttyUSB2 AT$QCPDPP=1,1,"","o2"
ERROR

Tue Mar 9 17:25:59 2021 : /dev/ttyUSB2

Tue Mar 9 17:26:08 2021 : /dev/ttyUSB2

Tue Mar 9 17:26:10 2021 : /dev/ttyUSB2

Tue Mar 9 17:26:11 2021 : /dev/ttyUSB2

Unfortunately, the internet connection still does not work.
I appreciate any advice on how to proceed.

Thank you!

Wireless Joint

WE826-Q - Is there an LTE modem?

WE826-Q - Is there an LTE modem?

Re: WE826-Q - Is there an LTE modem?

Re: WE826-Q - Is there an LTE modem?

Re: WE826-Q - Is there an LTE modem?