Wireless Joint

Hi all -- thanks for the help thus far!

I've got a WG1608 here with a Sierra EM7565. Came with OpenWRT pre-installed, but was incompatible and modem tab didn't show up. Flashed to GoldenOrb WG1608-GO2020-06-14, found modem tab. Put in APN and other settings as per FAQs (thanks) and still no go.

IMEI and SIM ID etc all the info shows up, but modem status shows: Modem Present/Not Connected

Clicking the "connect modem" button does nothing.

So I read more and found out I should probably downgrade firmware to WG1608-GO2020-06-10 and try again. So did hard firmware reboot, got to the Chinese screen, flashed with 06-10, and no go.

Modem Status still shows: Modem Present/Not Connected, button doesn't work

So I thought it was that the modem didn't have the right settings and couldn't connect to ATT, but now I think it's that the router is having trouble talking to the modem.

Are there some AT commands I need to run to "activate" or otherwise connect the modem and get it running or something? (That's probably what the button does?)

Also I've read conflicting reports on using carrier-specific firmware for the modem. The standard tutorial says use the generic for most cases, but others reply saying use carrier specific. What's the consensus at the moment? For ATT and Sierra?

Many thanks

shunryu999 wrote: ↑Fri Sep 18, 2020 2:10 pm Hi all -- thanks for the help thus far!

I've got a WG1608 here with a Sierra EM7565. Came with OpenWRT pre-installed, but was incompatible and modem tab didn't show up. Flashed to GoldenOrb WG1608-GO2020-06-14, found modem tab. Put in APN and other settings as per FAQs (thanks) and still no go.

IMEI and SIM ID etc all the info shows up, but modem status shows: Modem Present/Not Connected

Clicking the "connect modem" button does nothing.

So I read more and found out I should probably downgrade firmware to WG1608-GO2020-06-10 and try again. So did hard firmware reboot, got to the Chinese screen, flashed with 06-10, and no go.

Modem Status still shows: Modem Present/Not Connected, button doesn't work

So I thought it was that the modem didn't have the right settings and couldn't connect to ATT, but now I think it's that the router is having trouble talking to the modem.

Are there some AT commands I need to run to "activate" or otherwise connect the modem and get it running or something? (That's probably what the button does?)

Also I've read conflicting reports on using carrier-specific firmware for the modem. The standard tutorial says use the generic for most cases, but others reply saying use carrier specific. What's the consensus at the moment? For ATT and Sierra?

Many thanks

i have two wg1608 routes. one has EM12-G m.2 and the other has EM06-A m.2. bothr are running WG1608-GO2020-06-14. both connect without too much problems.

one thing i did notice you need to have an APN set or it will never connect. Router Login ==> Goto Modem ==> Connection Profile. Enter the correct APN for your carrier. i am on AT&T USA so i use broadband you can use broadband (usually used for tablets) phone (usually used for AT&T branded phones) nxtgenphone (usually used for unbranded AT&T phones). my friend who uses my other one with the EM-12G has to use phone as the APN to get his to connect to AT&T. i can use any one of the 3 to get it to connect.

you can also refer to https://openwrt.org/docs/guide-user/net ... figuration

and

[url]http://wirelessjoint.com/viewtopic.php?f=8&t=1085&p=7344&hilit=em20#p7344[/url]

both pages have useful information.

What service and plan are you using? Look in your System Log (System-->System Log) and see if you see anything that mentions "subscriber"

Go to Modem-->Miscellaneous-->AT command term. Enter the command Post the text it returns here

Thanks guys -- on ATT, tried out the 3 APNs, didn't know about the others! Noticed that my phone was using nxtgenphone though so I thought maybe that would do the trick. But no luck.

So on GoldenORB do I still need to install the QMI package? as per https://openwrt.org/docs/guide-user/net ... figuration

When I use WG1608-GO2020-06-14 I can't get the Luci GUI to "Save and Update" - it hangs when applying the update. On WG1608-GO2020-06-10 that seems to work.

But I don't think the AT Command window is working correctly. I tried setting the ATT carrier firmware https://wirelessjoint.com/viewtopic.php?t=692 and got an OK but then checked again and it hadn't changed. What am I doing wrong there?

Also on the SIM -- I did just pluck my iPhone SIM out and pop it into the router -- do I need to do something else with the account?

Thanks @Didneywhorl -- here's my output

Current Time: 477 Temperature: 35
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Not attached
LTE band: No band LTE bw: 1.4 MHz
LTE Rx chan: 0 LTE Tx chan: 18000
LTE SSC1 state:NOT ASSIGNED
LTE SSC2 state:NOT ASSIGNED
LTE SSC3 state:NOT ASSIGNED
LTE SSC4 state:NOT ASSIGNED
EMM state: Deregistered Attach Needed
RRC state: RRC Idle
IMS reg state: No Srv

PCC RxM RSSI: 0 PCC RxM RSRP: 0
PCC RxD RSSI: 0 PCC RxD RSRP: 0
Tx Power: -- TAC: 0000 (0)
RSRQ (dB): 0.0 Cell ID: 00000000 (0)
SINR (dB): 0


OK

I would stick with the 6/10 firmware. No extra packages needed that I know of.
I would use the Generic firmware, but I don't think its totally necessary.
You used the command AT!IMPREF=... command?

Looking at your gstatus output, the RRC Idle tells me your network isnt allowing you connection.
LTE PS State: Not attached definitely says your not connected to the networks data.

Make sure your AT+CGDCONT? output isnt littered with odd APNS

AT+CGDCONT?
+CGDCONT: 1,"IPV4V6","broadband","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0

Seems like a lot of zeroes. Tried all the different APNs, they showed up here, but no luck.

OK thanks for the help y'all, turned out to be the SIM -- tried another line on our plan and whammy! no problem - connected and doubled the speed of the MOFI4500.

But upload speed dropped by about 2/3, from 15Mbps to 5Mbps on the EM7565. Any thoughts there?

i had the same problem, the cause was the faulty m.2 to pciem adapter

Check my video review. Never use 06-14 version. It is faulty. Use 06-10 version
https://wirelessjoint.com/viewtopic.php?f=8& ... 865#p13865

There is a newer WG1608 version dated 23-Nov-2020 that runs like a scalded banchee on my WG3526.

I get speed increases of about 35-40% average both down and up and total max of 53gbit where 26 up and 6 down was my previous bests up & down speeds.

The WG3526 and WG1608 are very similar, mostly just updated chipset and M.2 interface instead of the mini PCIe slot.

roddel007 wrote: ↑Sun Nov 01, 2020 7:40 am Check my video review. Never use 06-14 version. It is faulty. Use 06-10 version
https://wirelessjoint.com/viewtopic.php?f=8& ... 865#p13865

Good video thanks for sharing. Where did you find a EM160 for sale? I've seen other people mention eBay, but I've yet to see one come up on there.

I've heard of others using the WG1608 firmware on the wg3526

BrandonDillon wrote: ↑Mon Nov 30, 2020 2:42 pm Good video thanks for sharing. Where did you find a EM160 for sale? I've seen other people mention eBay, but I've yet to see one come up on there.

thewirelesshaven.com will have some on the site by weeks end, hopefully.

Do you have an idea on pricing?

$225 each, including shipping.

Purchased one from here [mod edited]

punkguy00017 wrote: ↑Thu Dec 03, 2020 5:52 pm Purchased one from here....

He was talking about the EM160.

Is there a reason some att SIM cards get stuck on connecting? Only one out of the 3 att SIM cards I have will work.

Not sure. too many variables possible, but I have seen junk SIM cards too.