Page 1 of 1

UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 1:10 pm
by TerriVegan
AT!GSTATUS?
!GSTATUS:
Current Time: 572 Temperature: 36
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Not attached
LTE band: B26 LTE bw: 1.4 MHz
LTE Rx chan: 8716 LTE Tx chan: 4294967295
LTE CA state: NOT ASSIGNED
EMM state: Deregistered Attach Needed
RRC state: RRC Idle
IMS reg state: No Srv

PCC RxM RSSI: -80 RSRP (dBm): -95
PCC RxD RSSI: -84 RSRP (dBm): -98
Tx Power: 0 TAC: 0BBD (3005)
RSRQ (dB): -6.1 Cell ID: 00994C01 (10046465)
SINR (dB): 24.2


OK

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 1:58 pm
by swwifty
can you provide more info/details?

Looks like you are deregistered.

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 3:01 pm
by TerriVegan
AT!ENTERCND="A710"
AT!USBCOMP=1,1,1009
AT!CUSTOM="IPV6ENABLE",1 AT+CGDCONT=1,"ipv4v6","broadband"
AT+CGDCONT=2,"ip","broadband"
AT!SELMODE=2
AT!SELRAT=00
AT!BAND=00
AT+CFUN=1
AT!RESET

After
CODE: SELECT ALL
AT!ENTERCND="A710" AT+CNUM

I got results of:
AT+CNUM
+CNUM: ,"12292924525",129


OK

Then I put AT!LTEINFO?
AT!LTEINFO?
!LTEINFO:
Not Available


OK

NOW RUNNING:
AT!IMPREF?
RESULTS

AT!IMPREF?
!IMPREF:
preferred fw version: 02.24.05.06
preferred carrier name: GENERIC
preferred config name: GENERIC_002.026_000
current fw version: 02.24.05.06
current carrier name: GENERIC
current config name: GENERIC_002.026_000

OK


AT!GOBIIMPREF?
AT!GOBIIMPREF?
!GOBIIMPREF:
preferred fw version: 02.24.05.06
preferred carrier name: GENERIC
preferred config name: GENERIC_002.026_000
current fw version: 02.24.05.06
current carrier name: GENERIC
current config name: GENERIC_002.026_000

OK

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 3:08 pm
by TerriVegan
looks like I am connected now how ever the web/internet indicator dosen't glow and when I cannot it take a long time to reconnect, or I have to unplug it for the internet to pop up. this is what I am getting now.........


I have a MOFI4500-4GXeLTE-SIM4 4G/LTE Router AT&T
&
Netgear Nighthawk M1 MR1100 AT&T

They seem easier to use compared to this device. I just pop in my SIM and go.

Could it be the firmware? Is there another firmware option that will automatically configure without the AT COMMANDS?

AT!GSTATUS?
!GSTATUS:
Current Time: 344 Temperature: 50
Reset Counter: 1 Mode: ONLINE
System mode: WCDMA PS state: Attached
WCDMA band: WCDMA 850
WCDMA channel: 1087
GMM (PS) state:REGISTERED NORMAL SERVICE
MM (CS) state: IDLE NORMAL SERVICE

WCDMA L1 state:L1M_DCH LAC: 120C (4620)
RRC state: CELL_DCH Cell ID: 0D53587B (223565947)
RxM RSSI C0: -101 RxD RSSI C0: -91
RxM RSSI C1: --- RxD RSSI C1: ---


OK

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 3:17 pm
by TerriVegan
how do I get the internet indicator light to work? The globe light never glows.

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 3:35 pm
by TerriVegan
this is with my 4G LTE SIM CARD with external high gain antennas. The previous status was with my 4G only Sim card with no high gain outdoor antennas.


AT!GSTATUS?
!GSTATUS:
Current Time: 312 Temperature: 56
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Attached
LTE band: B2 LTE bw: 10 MHz
LTE Rx chan: 650 LTE Tx chan: 18650
LTE CA state: NOT ASSIGNED
EMM state: Registered Normal Service
RRC state: RRC Connected
IMS reg state: No Srv

PCC RxM RSSI: -95 RSRP (dBm): -136
PCC RxD RSSI: -91 RSRP (dBm): -119
Tx Power: 23 TAC: 2C34 (11316)
RSRQ (dB): -13.3 Cell ID: 0B537908 (190019848)
SINR (dB): 3.6


OK

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 3:39 pm
by TerriVegan
the internet is dropping and the speeds are slower than MOFI and Nighthawk MR1100. Using the same antennas and the same spot as the MOFI and MR1100, I get about 15 Mbps. Speed test bouncing me back 0 kbps, -1ms

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 4:08 pm
by TerriVegan
seems like it works better for me without the external antennas. We are in a rural area and I need to be able to connect them. How do I configure it so the external antennas can work?right now without the antennas we are getting
61ms
1.38 Mbps
228kbps upload
and thats over a WIFI connection

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 5:18 pm
by TerriVegan
now I have the external antennas working Im getting between 10-15Mbps download with a WIFI connect



AT!GSTATUS?
!GSTATUS:
Current Time: 1445 Temperature: 43
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Attached
LTE band: B2 LTE bw: 10 MHz
LTE Rx chan: 650 LTE Tx chan: 18650
LTE CA state: NOT ASSIGNED
EMM state: Registered Normal Service
RRC state: RRC Connected
IMS reg state: No Srv

PCC RxM RSSI: -90 RSRP (dBm): -116
PCC RxD RSSI: -93 RSRP (dBm): -120
Tx Power: 0 TAC: 2C34 (11316)
RSRQ (dB): -13.9 Cell ID: 0B537908 (190019848)
SINR (dB): -3.2


OK

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri Dec 14, 2018 7:42 pm
by swwifty
It appears that when you are using your small antennas on a router, you are getting too weak of an LTE signal to even connect, and hence getting the WCDMA connection. Are you positive you are aiming your antennas at the closest tower? Your signal stats in your first post look pretty good, but that was Band 26 with only a bandwith of 1.4mhz (which isn't going to get you much throughput. The last post shows Band 2 which has 10mhz, but the signal is extremely weak. What external antennas are you using, and I assume you are using them outside?

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Sat Dec 15, 2018 7:19 am
by TerriVegan
Right now the antennas are not mounted up high outside, they are inside. We are doing a soft run before installing.

So for that spot gives us the best download speeds compared to the rest of the house.

The antennas that I'm using I got from Amazon. It came with the TS9 Connectors for my netgear nighthawk mr1100 then I got the adapters to switch off and on with the MOFI,/now WE826-T.

Tupavco
Tupavco TP545 Yagi Directional Roof Antenna 3G/4G/LTE Wide Band 11dBi 700MHz to 2.7GHz Range 2FT Cable w/ 2FT RP-SMA Male Cable to TS-9 Adapter.

I ordered another pair from Ebay, awhile back, waiting on them to come.

Aperit Brand
High Gain 800~2700mhz 16dBi antenna CDMA GSM DCS AWS WCDMA LTE signal booster.
Application: Outside Antenna, Weatherproof
Frequency Range :800-2700mhz
Max. Gain (dB) :16dBi
Connector type : SMA female
Signal Transmission and Reception: Directional
Length: 17.3" (43cm)
Weatherproof

I thought about getting the Wireng Antennas, they just seem so expensive. $344.88 per pair

WideAnt2-X™ Dual Antenna for MOFI Network MOFI4500-4GXeLTE Router True MIMO Fully Enclosed Wide Band ±45° Polarizations (WideAnt-X™ 2)

WideAnt2-X™ Dual Antenna for Netgear Nighthawk M1 MR1100 True MIMO Fully Enclosed Wide Band ±45° Polarizations (WideAnt-X™ 2)

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Sat Dec 15, 2018 7:51 am
by Jim S.
Have you checked your antenna connections to the MC7455?

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Sat Dec 15, 2018 7:59 am
by TerriVegan
Yes I did they are on there nice and snug.

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Sun Dec 16, 2018 7:48 am
by swwifty
FYI these antennas "High Gain 800~2700mhz 16dBi antenna CDMA GSM DCS AWS WCDMA LTE signal booster" might not work with LTE. LTE bands start as low at 698mhz up to 2700mhz. Hopefully this is a typo (and granted all antennas pickup all signals regardless of their designed frequency, but you should still be aware)

I'd recommend looking at the The Wireless Haven store. They have a wide variety of antennas that are very reasonably priced.

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Sun Dec 16, 2018 8:03 am
by TerriVegan
Not a type O I copy and paste how they had it advertised.

I looked in the store and was going to. I was irritated with the shipping cost.

I'm still trying to figure things out.

I'm looking for cable to connect to the antennas. And flat mounting brackets for the antennas so I can hook up antennas on both sides to make it mimo
.
Screenshot_2018-12-16_001718.jpg
Image

Everything seems to be working. Antennas are still inside, I get between 10Mbps-20. Only issue is that the guest wifi is bringing that in while the master wifi ssid is less than 1Mbps.

AT!GSTATUS?
!GSTATUS:
Current Time: 45793 Temperature: 56
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Attached
LTE band: B2 LTE bw: 10 MHz
LTE Rx chan: 650 LTE Tx chan: 18650
LTE CA state: NOT ASSIGNED
EMM state: Registered Normal Service
RRC state: RRC Connected
IMS reg state: No Srv

PCC RxM RSSI: -94 RSRP (dBm): -117
PCC RxD RSSI: -95 RSRP (dBm): -118
Tx Power: 23 TAC: 2C34 (11316)
RSRQ (dB): -9.8 Cell ID: 0B537908 (190019848)
SINR (dB): 6.4


OK



How do I send the guest wifi info?


Image
I feel better now about this product. I returned my MOFI yesterday. The family feels that this is faster than the MOFI. The speed test MS # is much lower when you compare the 2.
Screenshot_2018-12-15_071118.jpg

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Sun Dec 16, 2018 5:39 pm
by swwifty
That's an interesting antenna mount.

I'm not sure what you mean about the guest wifi?

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Sun Dec 16, 2018 6:18 pm
by TerriVegan
The one the says "guest" gets faster download speeds while the master one "daveed stop farting" gets less than 1Mbps. How do I fix that?

Image

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Mon Dec 17, 2018 4:48 am
by swwifty
lol, nice ssid name.

That bitrate i believe is only an estimate, it doesn't mean your guest will get faster or slower speeds than your main wifi.

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri May 17, 2019 3:15 am
by TerriVegan
AT!GSTATUS?
!GSTATUS:
Current Time: 1730 Temperature: 50
Reset Counter: 4 Mode: ONLINE
System mode: LTE PS state: Attached
LTE band: B2 LTE bw: 10 MHz
LTE Rx chan: 650 LTE Tx chan: 18650
LTE CA state: NOT ASSIGNED
EMM state: Registered Normal Service
RRC state: RRC Connected
IMS reg state: No Srv

PCC RxM RSSI: -94 RSRP (dBm): -118
PCC RxD RSSI: -96 RSRP (dBm): -121
Tx Power: 0 TAC: 2C34 (11316)
RSRQ (dB): -11.5 Cell ID: 0B537908 (190019848)
SINR (dB): 3.4


OK

Re: UNABLE to connect to AT&T internet WE826-T & MC7455

Posted: Fri May 17, 2019 3:26 am
by TerriVegan
LTE CA state: NOT ASSIGNED

Is that an issue?

I have to constantly keep rebooting, I keep losing internet signal all throughout the day. It's been like these the past 2 weeks or so.

I've reset and flashed over to the The Rooter Project. Same it issue