Page 1 of 1
x86 goldenorb EM7565 and Simple Mobile
Posted: Wed May 13, 2020 2:51 pm
by jasonh
All,
This could get a bit confusing with all of the various pieces and parts. However, I have a Proxmox VM of x86 goldenorb built on OpenWRT 19.07.2. I have an EM7565 in a USB 3.0 enclosure and I'm passing that USB device to the goldenorb VM.
I've tutorial'd my way through most of this and have the modem recognized and can send AT commands, etc.
I'm on Simple Mobile. SIM was activated, and though I don't have a phone to test it in, it appears that I'm connected (I could be dead wrong here). But I am showing "Normal Service" from AT!GSTATUS?:
Code: Select all
AT!GSTATUS?
!GSTATUS:
Current Time: 1975 Temperature: 26
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Attached
LTE band: B66 LTE bw: 5 MHz
LTE Rx chan: 0 LTE Tx chan: 132547
LTE SSC1 state:NOT ASSIGNED
LTE SSC2 state:NOT ASSIGNED
LTE SSC3 state:NOT ASSIGNED
LTE SSC4 state:NOT ASSIGNED
EMM state: Registered Normal Service
RRC state: RRC Idle
IMS reg state: No Srv
PCC RxM RSSI: -77 PCC RxM RSRP: -98
PCC RxD RSSI: -84 PCC RxD RSRP: -105
Tx Power: -- TAC: b0f9 (45305)
RSRQ (dB): -7.2 Cell ID: 00775a20 (7821856)
SINR (dB): 26.0
OK
I'm unable to connect out over the wwan, though. Checking ifconfig I have nothing by RX/TX errors on wwan0. As well, I have non-stop messages of:
Code: Select all
cdc_mbim 2-1:1.12 wwan0:kevent 1 may have been dropped
cdc_mbim 2-1:1.12 wwan0:kevent 0 may have been dropped
I'm hoping someone here will be able to point me in the right direction. Here's some more info I can provide that may be beneficial:
Code: Select all
AT+CGDCONT? +CGDCONT: 1,"IPV4V6","simple","0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0",0,0,0,0
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Wed May 13, 2020 3:14 pm
by Didneywhorl
jasonh wrote: ↑Wed May 13, 2020 2:51 pm
RRC state: RRC Idle
IMS reg state: No Srv
This part right here says you may want to put the SIM in a phone first and verify it's getting internet. I've seen this before I believe.
I could be wrong but I think it says, you connected to the tower, but you are denied.
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Wed May 13, 2020 4:08 pm
by jasonh
Doh! Looks like I'll have to track down a compatible phone.
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Wed May 13, 2020 8:36 pm
by jasonh
Alright, I was able to get the SIM in a phone. Made a couple calls, visited a couple websites, ran speed test, watched a youtube video...
Popped the SIM back into the USB 3.0 enclosure and I'm at the same spot as before.
Code: Select all
EMM state: Registered Normal Service
RRC state: RRC Idle
IMS reg state: No Srv
Any other pointers?
I've got the APN as:
But, under Modem > Network Status > General Information it's showing:
Code: Select all
Modem: Sierra Wireless, Incorporated EM7565
Modem ID: 1199 : 9091
Provider: HOME
Comm Port: /dev/ttyUSB1
Temperature: 26.00°C
Protocol: MBIM
The "HOME" part looks curious, and I think I've seen that as an issue in another post about Simple Mobile.
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Wed May 13, 2020 10:03 pm
by jasonh
Alright, I put the EM7565 in QMI with:
RRC state shows:
I can now ping out. I'm too new to this part of things to understand exactly the reasons behind MBIM vs. QMI, but evidently the EM7565 wasn't happy without QMI.
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Wed May 13, 2020 11:38 pm
by BillA
jasonh wrote: ↑Wed May 13, 2020 8:36 pm
Alright, I was able to get the SIM in a phone. Made a couple calls, visited a couple websites, ran speed test, watched a youtube video...
Popped the SIM back into the USB 3.0 enclosure and I'm at the same spot as before.
The "HOME" part looks curious, and I think I've seen that as an issue in another post about Simple Mobile.
Make sure to set the TTL to either 64 or 65. Try both, because only one of those values will work without using hotspot data, which you will find out as soon as you have used up the first 5gigs of data. If it stops with 64 after a while, just change it to 65.
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Fri May 15, 2020 1:06 pm
by Didneywhorl
jasonh wrote: ↑Wed May 13, 2020 10:03 pm
I can now ping out. I'm too new to this part of things to understand exactly the reasons behind MBIM vs. QMI, but evidently the EM7565 wasn't happy without QMI.
I overlooked that bit. Sierra created the QMI protocol I think. Their modems seem to work much better in QMI. I wouldnt think that MBIM wouldn't work though.
AS BillA stated, make sure you set the TTL values.
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Sat May 16, 2020 10:21 am
by jasonh
Doing all good with QMI and TTL at 65. Didn't have to set up mangle, as no hotspot data usage is showing. So, despite everything not being in its final location (I'm moving at the end of the month) connection seems to be doing alright.
I do notice that the EM7565 is showing USB 3.0 speeds in the hypervisor:
shows:
But, in the goldenorb VM I'm getting USB 2.0 speeds:
Checking
Shows:
Code: Select all
SUPPORTED:Super-Speed
CURRENT:High-Speed
I've set it as:
But, from my understanding that's just setting the maximum supported speed (Which is already correct).
I'm willing to bet that it's a difference in the kernels and the drivers being used. It's sort of evidenced in the "Driver=qcserial" portion of the goldenorb output.
Just not sure if anyone has run into this before, and exactly what the fix might be.
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Sat May 16, 2020 12:22 pm
by Didneywhorl
Odd. So goldenorb is detecting the usb2 bus but your shell commands show the device in usb3? It may likely be your vm interface. Are you using docker?
Re: x86 goldenorb EM7565 and Simple Mobile
Posted: Sat May 16, 2020 8:28 pm
by jasonh
I'm using a Proxmox kvm. I doubt that I'll come anywhere near needing 3.0 speeds. So it isn't high on the priority list right now. Just odd that it's not defaulting to 3.0 on both.
The kernel versions are pretty different between the two, and I'm sure that plays a role.