Wireless Joint

Yes my email is in the first post or my skype
live:kcphonestores_1

What you need to do depends on what carrier you are going to use

edeleonp wrote: ↑Sat Sep 21, 2024 9:45 am Greetings guys, have you found an easier solution to unlock this modem?

No maybe someone else has, I have no plans to do any more work on this device.

viewtopic.php?p=29211#p29211

I had not planned on it, that would lead to about a thousand emails and msg's for support for all the people that mess their devices up fooling with it. cross flashing is very risky and I did not test this at all other than letting it run for a day, I have not even picked up a t10 since that day.

It is

https://acupdates.netgear.com/swiwu/updates.aspx

I can do custom menus for it, band lock yes,tower lock no I am not sure it can be done on the device, vpn can be done already by the user and ttl and imei yes I can do that.

@moddermod You are calling me out in public for not opening up my hard drive to you for anything you want from it? Not cool at all. let me explain something to you, I do this for a living, while your at work or sleeping or out with your friends or whatever it is you do, I am working every day, every ...

make a raw dump containing the spare and use that for the t10, as long as your nand registers and nand controllers are correct it will should load and run fine, however , be smart and first make a backup of the t10 in case it goes wrong so you can at least get back to a working device.

There is no need anymore to take a chance and reload firmware to your devices that are locked out of
openmep, this can now be fixed without the need to reload them, all MRxxxx devices supported m1. m5, m6

Does your device still work and get service?

Yes I do still need one I have a 6150 arriving in a couple of days. I can send you my 6500 to play with once I get the 6150 setup. I'm willing to risk it getting bricked if you can figure out how to port the modem firmware from the 6550 and open all the bands. Ok sounds good Hey Rich Hathaway , I ...

Yes I do still need one

WJUser wrote: ↑Fri Aug 16, 2024 1:03 pm
I haven't messed with routers for a while. Is this a FTDI thing or straight USB?

USB

The factory backup in these inseego devices is not a snapshot of your firmware, it is a file with about 30 or so .dat files amounting to a total of about 80 kilobytes it is nv and efs items is all and cannot reload or restore your firmware. below is the decompiled factory backup of the m3000 factory ...

Yes imei can be changed and band can be locked on the fg but it is a pain to get the ports enabled on that one

There are lots of different ways to do this here is the update address update url2.PNG or in the nv set WU_AUTOCHECK to 0 It wont check for updates unless you tell it to or change WU_UPDATEURL to anything else or change WU_AUTH to anything else and it wont be able to pass the login to get the update ...

Where can i get ahold of the t9 firmware you are using? It is not a public file, I have not posted it anywhere. have you tested it? Not really, I made it for the T9 and have tested it on that device fairly well but did not do much if any testing on the T10 besides loading it and running it for a ...

Yes it would work fine however you must know it may get messed up beyond repair so if you cannot afford for this to happen to it then hang on to it.

On your device the boot part is not intact thus making only 9008 (emergency) mode available, there may be other problems with it but I cannot know that until it has a proper boot part loaded back to it which I do not have yet.

Load the 6110 build back to it and it should work ok again after that.

The goal of this thread is to make and post loadable firmware for this device with a simple recovery/firmware-loader tool to aid in recovery and/or upgrade/downgrade of its firmware free of charge to anyone who wants it. Someone from here sent me one of these devices but unfortunately it cannot be ...

read my post a few posts above this one dated july 11th it states I do not have a 6550 or 6xx0 now to continue this project, The ones I had had to be returned to the rightful owners. thus it is on hold until such a time when I can have these 2 devices in hand again. This is all I do these days ...

Rich Hathaway wrote: ↑Sat Mar 02, 2024 7:44 am There are risks involved anytime you load firmware, however they are much greater when using cross sku's and when you dont increment versions by one like they are meant to be.

For now beta testing is closed, as it stands now everything done is tested fairly well and while work still needs done on this I do not have a 6550 I can work with at the moment, a few people have allowed me to work with their 6550 devices and a big thank you to them, I need one I can possibly bork ...

look here please, this is not the place to solicit services

viewtopic.php?p=28947#p28947

Yes of course

seloka190 wrote: ↑Wed Jun 05, 2024 7:20 am what about qtools
anyone try it with netgear ?

Qtools requires a signed or properly patched loader to work.
There is/are no known or leaked loaders beyond SDX20 for these devices so we
are stuck with fastboot for now.

telnet is already enabled on this model and this platform with no need to do anything to enable it Port 5510 is open on it, whatever you used to scan ports was wrong and misread the ports, there are several other ports open on this device and firmware then what you listed, perhaps its time for you ...

I would love to know how to fully flash FW into these devices. That wont happen until a loader is leaked/found and patched for these chips, the best you can do now is to build your firm for each partition and load via fastboot. I can verify you can erase all parts via fb and load them back ...

Alainx wrote: ↑Tue May 28, 2024 5:58 am Hello, I have a MR6550-APS with FW 12.01.44.00, is there any means to enable telnet and AT commands?

It should already be enabled in that one, are you sure it is not MR6500 model ?

Those are usually for the antennas that are either on the midframe if it has one or the outer frame

I dont know, pm me your skype name and ill look

I spoke to you already yesterday via skype, I am the same person.

NO the architexture is different, the fg is a 26 partition layout and the fg2000e is a 28 partition layout and since there is no known loader for it it is not possible to change it over via fastboot, meaning you are stuck with the layout and its firmware that are on it so only loading firmware from ...

roaminggnome wrote: ↑Sat May 04, 2024 3:58 pm
You're just going to have a bad time using a 6500 on Tmo since it doesn't support any of Tmo's 5G bands.

6500 works fine on tmobile

6500 on tmo.jpg

That one is kind of a rare one, I personally have never seen it, I own most other inseego models but not that one so I wont be much help, I did make a port tool that works on most of them I am not sure if it would work on that one for the adb port or not.

900E is download mode which needs the loader NPRG-SDX55 (Normal Program Mode)
9008 is emergency mode which needs the loader ENPRG-SDX55 (Emergency Program Mode)

That depends on what you mean by edl, edl to me means the mode (emergency download mode which is 9008)
if you mean edl as in BK's tools then I do not know I dont use BK's edl tools except for the keygen.

I have factory loader but it is not working, there is no known working loader for this device leaked or patched yet.

Oh ya my bad this one just hold reset and plug in power while usb is connected and hold for 5 seconds after that, sorry I have been in sierra threads today and was thinking sierra not inseego lol. If you still only get 900E it means the boot part is borked and you will need to use a testpoint or ...

900E is download mode, not bootloader.
fastboot mode on these is hold reset button pop in battery keep holding reset and plug in usb and keep holding reset for 5 seconds or until your pc dings then will be in fastboot mode.

you need to load from bootloader (fastboot) not from download mode

its right above your post

I got sidetracked on this project and stopped working on it, it was not a funded project so there was no rush anyway, I just wanted to see if it would work on ios and it did.

kcphonestores@gmail.com

wow I really mis cdmaws, I used it more than any other tool, my background is in cdma.
im going to send you a pm about something.

Looking for the correct command to disable LTE for troubleshooting. Thanxs if it has a qualcomm cpu (I think it does x55) just use offline-D mode you can get to it by sending the dm command 290100 you may need to send the spc first if it does not respond send the spc like this 41 30 30 30 30 30 30 ...

There are risks involved anytime you load firmware, however they are much greater when using cross sku's and when you dont increment versions by one like they are meant to be.

I am waiting on another 6550 to arrive here to continue this work, I do not have this model on hand right now

That is because these factory packed firms (spk/cwe) do not write all parts, especially the parts you need it to. and some of them it only writes generic or non specific values, such as parts of the efs, userrw, cust and hdata. you can see my screenshot to compare the devices partitions and the ...

Well I am sure there is more than one way to skin a cat, I use a patched modem for these devices since they are so locked to uscell.

There should be no spaces in those AT commands unless you are using some tool that was coded to need a space.
I do not have that device but those tracfone devices usually do not have this access, they lock them down pretty good.

You should be able to boot it up without a sim so you can work on it without it updating.
I can kill updates for you if you need it.

This is working without issue running on any mr6xxx device but enabling bands is still having some trouble there are a couple of us working on it.

Yes I can restore the openmep function on it for you so you can repair the imei again, you can send me a pm about it.

Your ports are already enabled? I ask because this (network turned off) happens usually when someone has been sending commands or editing files trying to do something.
But the answer is the same as I told you over at xda, reload the firm or the modem partition and it will be restored to "on"

remove battery and cable then hold reset while you plug in the cable and keep holding reset until your pc dings (about 5 seconds)

Someone sent me this device to look at and since I just did the T9 I took a look at it. It is basically just a t9 with a slightly bigger screen and a slightly diff board layout but almost the same It is so similar I loaded t9 firmware to it and it runs fine with it. You can see here my clone of t9 ...

Yes this is a constant work in progress because so little is known about 5g hacking currently, what band are you needing to pickup?

I have all the betas I need at the moment. To update this thread, the 6550 loads and runs fine on 6500 and most of the features one would want work, such as, it is unlocked, the AT&T branding is gone, the menus reflect the 6550 firm, bands are working but it wants to keep using the 6500 bands still ...

If you want to get it serviced, my email is in this first post
viewtopic.php?p=28223#p28223

there is none out there, I had to make my own, you will prob have to do the same.

Thats not good. what it takes to fix it will depend on where it was with the update when you unplugged it, but no matter where it was it will need firmware loaded to it

This firmware is not public or posted anywhere.

Thats not unusual at all, Tracfone is very proprietary and most of their devices break away from the norms of other same line/class devices, this is true with their phones and data devices. however they seem to always have some similarities to other same class non TF devices, they are always high ...

Guys, why did you even decide that MR2100 can be flashed through FDT? No one decided it can be flashed via fdt, perhaps you did not read this thread, his device will not boot up so that tool cannot work here. his device can only boot to factory download mode which is the mode fdt requires to run ...

It works on yours because 6450 is a non-branded device, it will not work on the 6500 that the op asked about.

its interesting your 6450 is still also using the old algorithm on newer firmware, the other devices/firmwares in this class (MR) use the new algo.

Yes of course, but this forum is not my personal sales thread so pls msg me away from here.

the image name is wrong unless you changed it, that is fdt's current problem

AKosterin wrote: ↑Sun Jan 07, 2024 8:14 am If you select "-d SDX55" in sierrakeygen for !OPENMEP, it will OK

it does not work on 12.01.xx with this update they removed the OPENMEP function

I tried: fdt2.exe -i <filename> then: fdt2.exe -f <filename> (separately of course). Friend, if this is what you input then it would not have run at all, it seems to me that if you really want help you would be eager to answer. I ask again pls run it and copy and paste the query and result here

how it would help is to know the exact command you wrote since it is giving you a command error this would be needed to know.

It may load fine on a working device but not recover yours because it is missing a partition that happens to be borked on your device.

Search found 589 matches