Wireless Joint

Well I dont like messing with my router to much as its my sole source of internet other then my phone, so I figure will let someone else flash and tell me if the interface is in there

correct, even things like apn and ttl will need to be typed back in after a flash

I have run in the past rooter, official pre builds of goldenorb and wifix all interchangeably. I do seem to recall there were some instances where I had to do the Full Factory Reset method where my router was put all the way back to its chinese boot and then load up the individual firmwares.

As far ...

I use the b66 with ca to b66 as my main setup. I have my bands locked to 66 only. What the CAA part does is as follows:
The initial connection to band 66 in my setup is either 20mhz or 10 mhz seems to depend on something on the tower side that I cannot control. The CAA kicks in when the tower deems ...

CA is determined by the tower as to when and if its implemented. The modem has specific combinations thats are allowed for CA. My modem EP06-A allows CA of 66 to 66 so I simply locked my band to 66 only.

Mind you this solution is customized to my setup. Band 66 may not be the best band in your area ...

I would also be intersted but as well interested in a basic changelog of whats been updated since the may 2020 build i am currently running.

Also differences between wifix which i am using and rooter, as rooter has a version dated 8-15-2021. Would personally rather stay with wifix as the support ...

What they are doing there is locking to specific cell radios on their tower. This allows you to force the radio to use only very specific radios on one tower. This way, if you can figure out your absolute best radios (Info from AT+QENG="servingcell" and "neighborcell") you can use QNWLOCK to force ...

May I ask which booster(s) you were using?

Hiboost 10k... Absolute requirement for making phone calls from my house (native signal without it was like a -116). So like you I already had the equipment in place and was like I wonder if I could use this to help my internet solution as well. For the ...

dbshelton wrote: Sat Aug 28, 2021 8:05 pm Not yet. Probably will tomorrow. Not sure where I am going to put it yet. I really don't think the current location is best.

I think the basic rule of thumb is to put it on one edge of the roof and don't aim across your roof. Always aim away from the house.

I would go back to a full factory reset... where you get the chinese load screen and try to load the firmware clean. If you get the same results I would go back a version and see if the problem still exists.

There is a previous version posted in the same area from feb 2021

There is also a version ...

ok...
https://www.vpnunlimited.com/help/manuals/how-to-manually-create-vpn-conf

In step one pick the manually create new device

Step 2
just pick a server you want to use. I would just pick one in the USA

Step 3
In this document I dont see a choice for wireguard let me know if when you are doing ...

I would do a factory reset the put back just the apn and ttl settings, nothng else. That should get you back to working, At that point we can try and tackle the vpn again if you choose.

Well satellite will ALWAYS have very bad latency its just part of how satellite works.

As far as your setup I think we are at the point of the old adage

"If it aint broke dont fix it"

:)

Congrats you are now to the point you shoudnt have to worry about these things anymore and just use it.

far as i know the "conventional router" would have to be running some form of goldenorb to be able to use the usb/modem card.

I have had my wg3526 running over a year 24/7 and no issues.

All of your above research is correct, though we do not talk details about changing imei in here as TECHNICALLY its illegal to be doing that. From my limited knowledge you will need to reseach the exact At command on your own but the quectel modems are the easiest to do this on while the sierra ...

dbshelton wrote: Tue Oct 05, 2021 5:17 am Good point. Now I am using an Archer AX21 router as an access point and the Wifi is much better than the NEX.

I use a low end archer c8 and its also much better. Router cost me like $40

in my area dsl isnt even an option. so no cable option at all.telco lines are 20+ years old and dsl has been "full" for over 7 years. Satellite is completely oversaturated both viasat and hughesnet cant even get 1 meg down. Cell access is so bad cant even make a reliable call without a booster or ...

ok yeah i think i remember this now from earlier in this thread. Since you already have a 75 ohm booster and its working I would do like I have in my home and have 2 seperate systems.

A booster for phone use (use your 75 ohm booster system)
A router for internet, in my case a wg3526 with an EP06-A ...

from a different thread but they had simular issues
Have you tried resetting the modem?

Should be AT+QPRTPARA=3 then after it reboots AT+QPRTPARA=1

ep06-a the connectors are larger and you wont need a pcie adaptor.

+1 as well for quectel being easier to work with

going from memory i think i used the router reboot option, may have been modem reset, try modem reset first as it takes less time for the router to recover.

I used the google DNS server as the tracking ip
8.8.8.8

I would set ping count to 3 or change interface down to 1

and i think i set ping ...

If it aint broke dont fix it

This may sound stupid, but if you need to move the antennas 10 feet farther away from the router is it possible to relocate the router 10 feet closer to the new antenna placement? Maybe put it in an attic? Move the router to an externally closer spot?

I had an issue like yours and ended up cheating ...

I can remember back when I was testing antenna location putting the antenna on top of a pole on top of a bucket on top of a ladder and moving the router to areas that made no sense at all but the idea is test with what you got in anyway you can and IF you determine that the new setup REALLY is ...

I am also on verizon in a very fringe area. No chance for coverage from anyone BUT verizon actually. The deprioritization issue is on the verizon side and I know no way around it other then getting a different plan with more "high speed" data.

Now as far as the basics on what to do....

In my ...