Search found 13 matches
- Sun Aug 23, 2020 11:05 am
- Jump to forum
- Jump to topic
Re: Cradlepoint CBA850 with MC400LP6
first thanks to all that contribute to this great forum, i learned a lot this week searching and reading. now i need some help as i'm new to lte internet.
i first tried a WE826-T2 then a mofi 4500 and had decent results on At&t. both used band 2 for the fastest speed, here i have b2 12 and 30. b2 ...
- Mon Aug 24, 2020 6:47 pm
- Jump to forum
- Jump to topic
Re: Cradlepoint CBA850 with MC400LP6
You are missingmotrac wrote: Mon Aug 24, 2020 11:35 am not sure why but command doesn't work? i have no problem with other commands?
Code: Select all
AT!ENTERCND="A710"
- Tue Aug 25, 2020 3:46 pm
- Jump to forum
- Jump to topic
Re: Cradlepoint CBA850 with MC400LP6
Trymotrac wrote: Tue Aug 25, 2020 7:36 am thanks that worked but band didn't change, stil on band 30 with ca on 12?
l still can't find where to enter start up command, so when i reboot the setting goes back to all bands.
Code: Select all
AT!RESET
- Wed Aug 26, 2020 8:20 am
- Jump to forum
- Jump to topic
Re: Cradlepoint CBA850 with MC400LP6
thanks, all commands were accepted but after AT!RESET still locked to band 30 and CA on 12?
I don't think you actually set the bands you wanted but instead just added to the list.
Does AT!BAND=? list "0F" you added?
Does AT!BAND? respond with "0F" you selected?
If not, you type AT!BAND=0F ...
- Wed Aug 26, 2020 9:35 am
- Jump to forum
- Jump to topic
Re: Cradlepoint CBA850 with MC400LP6
thanks, after following your instructions it now it works.
if the modem reboots will i lose this setting since i can't find when to enter the AT config script?
also what would be the command to lock to b2 and CA on b30, please?
Your modem shouldn't change the setting after reboots.
To lock B2 ...
- Thu Aug 27, 2020 9:43 am
- Jump to forum
- Jump to topic
Re: Cradlepoint CBA850 with MC400LP6
first thank you for all your help.
i thought you have to enter the command in the AT config script? that's what i can't find.
i have the modem set up to reboot daily @ 3am and this morning it was back to b30, ca 12 because i can't find the WAN interface profile to set the bands.
also
AT!BAND=1F ...
- Thu Aug 27, 2020 12:23 pm
- Jump to forum
- Jump to topic
Re: Cradlepoint CBA850 with MC400LP6
Ah. Exactly what I suspected. Hopefully you got it all sorted out now.motrac wrote: Thu Aug 27, 2020 11:02 am thanks, found it, there's a box checked that says "enable band 30"
- Tue Sep 01, 2020 6:59 pm
- Jump to forum
- Jump to topic
Re: ZBT-WE826 Band lock?
PCC RxM RSSI: -84 RSRP (dBm): -119
PCC RxD RSSI: -82 RSRP (dBm): -118
Tx Power: 23 TAC: 3419 (13337)
RSRQ (dB): -18.3 Cell ID: 0AC60308 (180749064)
SINR (dB): -3.0
Signals are bad. You could set it to use all bands first so it connects to the best one with better signals.
AT!ENTERCND="A710 ...
- Wed Sep 02, 2020 4:44 pm
- Jump to forum
- Jump to topic
Re: ZBT-WE826 Band lock?
thanks, ok i adjusted the antennas and improved the signal and read the tutorial but still not able to set for b2 and b30?
entered these commands:
AT!ENTERCND="A710"
AT!BAND=0D,"B2+B30",0,20000002
AT!RESET
but now getting b2 with ca on b12? trying to get b2 with ca on b30.
AT!BAND=0D,"B2+B30 ...
- Fri Sep 11, 2020 5:56 pm
- Jump to forum
- Jump to topic
Re: Cradlepoint CBA850 with MC400LP6
After you created band group 0F did you set it?
Code: Select all
AT!Band=0F
- Sat Sep 19, 2020 1:21 pm
- Jump to forum
- Jump to topic
Re: CBA850 no valid i.p. address
Cradlepoint uses the modem in the usb enclosure so yes you can take that enclosure out and put in it your router to test. Since you fail to get a valid ip address from the CP, have you tried the second LAN port which is set for passthrough?
- Sat Sep 19, 2020 6:00 pm
- Jump to forum
- Jump to topic
Re: CBA850 no valid i.p. address
You could manually set the address to see if it would let you access it. IP: 192.168.0.5 Netmask: 255.255.255.0 Gateway 192.168.0.1 or 192.168.10.5 / 255.255.255.0 / 192.168.10.1
As for the lights, it should be in the CP manual. Look it up for your model.
As for the lights, it should be in the CP manual. Look it up for your model.
- Sun Sep 20, 2020 5:10 pm
- Jump to forum
- Jump to topic
Re: CBA850 no valid i.p. address
You might've bricked your router during firmware update is what I think.