Ok, so I'm going to post a butt ton of pictures here on how I put together a WG3526-P Router w/Sierra MC7455 Modem inside a DM25X19 Antenna. The pictures will be posted on this thread as a series of posts instead of one SUPER long single posting.
NOTE: It is recommended to build and configure the ...
Search found 9 matches
- Mon May 11, 2020 5:29 pm
- Jump to forum
- Jump to topic
Re: What Modem should I use to replace coolpad hotspot from Mobile Citizen - sprint
All those are good to hook directly up to the enclosure, I believe.
External, outdoor, antennas are a big discussion. I always recommend the highest gain antennas you can afford, always a pair if you can.
I prefer directional flat panels. They are less picky as yagi type directionals, as they ...
External, outdoor, antennas are a big discussion. I always recommend the highest gain antennas you can afford, always a pair if you can.
I prefer directional flat panels. They are less picky as yagi type directionals, as they ...
- Mon Apr 06, 2020 5:25 pm
- Jump to forum
- Jump to topic
Re: EM7565 Verizon support
We have one Verizon unlimited data only reseller that we have worked for a couple of years. He said a few days ago that he still had a few slots open.
If you will reach out to us on the store via email, we will send you his contact info.
If you will reach out to us on the store via email, we will send you his contact info.
- Sun May 31, 2020 3:43 am
- Jump to forum
- Jump to topic
Re: Powering EM20-G in adapter enclosure
Why not just install the modem into the router? It would be much simpler, unless you want to install the modem/enclosure at a remote location (you didn't specify). In that case you would need to plug a USB3 hub into the router with a minimum 2amp power adapter for the hub, then plug then modem ...
- Sun May 31, 2020 3:07 am
- Jump to forum
- Jump to topic
Re: Using 4 4G LTE antennas in WG3526 (with EM20-G)
Unfortunately you can't reuse the existing WiFi antennas/cables since they are soldered onto the main board, but you can reuse two of their holes. Here's a couple of ways to do it.
If you're only using WiFi 2G or 5G at a time, then you could use the existing holes of the unused WiFi antennas to add ...
If you're only using WiFi 2G or 5G at a time, then you could use the existing holes of the unused WiFi antennas to add ...
- Wed Feb 19, 2020 12:05 pm
- Jump to forum
- Jump to topic
Re: Quectel EP06-A AT commands for carrier aggregation bandlock?
Hello,
Was looking thru the info on the link in this chat.
Showing the AT commands for the Quectel EP06-A AT commands for bandlock.
I have the Quectel EC25-AF.
Does anyone know if the AT commands are the same on it as the Quectel EP06-A?
Enter the following AT commands, and write down your ...
- Wed Jun 17, 2020 4:43 pm
- Jump to forum
- Jump to topic
Re: EM20-G won't connect. Please help
I notice the router is passing the APN "r.ispsn" to the modem so I assume you are using Sprint.
I seem to remember the Quectel modems need to be placed in LTE only to use with Sprint.
I seem to remember the Quectel modems need to be placed in LTE only to use with Sprint.
Code: Select all
AT+QCFG="nwscanmode",3,1
- Thu Jun 18, 2020 12:13 am
- Jump to forum
- Jump to topic
Re: EM20-G won't connect. Please help
CPBR reads phone book entries... Not sure why it's even attempting that, but it's probably erroring due to an empty phone book..?
C5GREG might be a typo for CGREG, which just checks GPRS registration, or it might be for 5G, which the EM-20 doesn't support. Either way, it can be ignored since no one ...
C5GREG might be a typo for CGREG, which just checks GPRS registration, or it might be for 5G, which the EM-20 doesn't support. Either way, it can be ignored since no one ...
- Tue May 31, 2022 8:43 am
- Jump to forum
- Jump to topic
Re: Switched from Sprint SIM to T-Mobile SIM (Calyx), but can't connect. CME ERROR: 13
Did you modify the modem to match the identity of the hotspot? It seems to be a requirement now.