Wireless Joint

^ This would be preferred.

I also wanted to clarify, it's up to the tower to allow CA over a band mix and band-locking might disable that compatibility.
If band-locking is being done because other bands don't provide the expected throughput, it's unlikely the tower will allow CA to occur unless a ...

The router will need roughly 60W-70W of available power for itself on poe. 72W POe injectors are what I use, the The Wireless Haven store on facebook has them.

The cat20 modem will FOR SURE work better, it will just be overkill for your router. A cat 6 modem is great, a cat 12, like the Quectel ...

Didneywhorl wrote: Wed Dec 09, 2020 5:57 pm The latest version fw for the EM160R-GL is version A04. (EM160RGLAUR02A04M4G)

Though I do not yet have a copy, I only have A03 on file. The newest modems received already have A04 on them.

Thank Didney! I will try to keep emailing them to see if they will send me the new firmware

Didneywhorl wrote: Wed Dec 16, 2020 5:16 pm It should be fine to use an adapter, but I would get a usb to m.2 direct adapter.

I finally got it to work, for some reason it did not like usb 3 ports.
Again thank you so much for your help !!!

Does anyone know the AT commands for the EM160R-GL? I cannot get the usual commands from the excel sheet to work, it just errors out. I suspect I am band locked to 66 right now. My old ep06a would CA 4&12 and 66&12 the em160 is stuck on 66.

Thank you
Josh


Nevermind guys, found this:
https ...

Are you mixing the antennas?

One 2x2 MIMO antenna should be attached to M and D/6 and the other 2x2 MIMO antenna should be hooked to M1 and M2. If they are mixed you will have issues I believe.


See if the modem is set to Data centric use. AT+QNWPREFCFG="ue_usage_setting",1 Though I honestly don ...

I don't know the answer for this question, but I can answer your question about changing the GoldenOrb DNS servers. GoldenOrb out of the box does not have an assigned name server, it defaults to whatever your ISP uses, you can change that though Network and Modem.

Network --> Interfaces --> Lan ...

Didneywhorl wrote: Sun Jan 10, 2021 2:46 pm iptables should apply the mangle to all traffic through the interface specified. I think at least.

Thank you so much Didney !

Didneywhorl wrote: Wed Dec 16, 2020 11:20 am That is the latest version for sure.

Here is another version they sent me, will be some time before I can update:
https://arkomasurvey-my.sharepoint.com/ ... Q?e=ihYgPI

Maybe the CA problems are fixed?

Obviously there are some hardware/software differences between those routers, but you should be able to tweak it to make it work. If you're using any kind of router behind a mobile router, you would want to set the mobile router into bypass mode so it doesn't do any routing/firewall functions, and ...

I'm sure the antenna was correct, I put the stock antenna back on for now. firmware check shows update available but can not get the page to open just shows page not found.

http://ofmodemsandmen.com/upload/WG1608-GO2020-12-24c.zip
that has 18.06

http://ofmodemsandmen.com/upload/WG1608-GO2020-12 ...

@vahnwinkle

I gotchu.

Get winSCP and putty if you don't have both apps for Windows : https://www.ofmodemsandmen.com/winscp.html
(Im not much for Mac so if you use mac, find equivalents and adapt the instructions for your OS.


Get the appropriate modem firmware update and unzip it somewhere you ...

You have to manually set your IP on your PC to your newer subnet (turn DHCP off) and access the GUI before the time runs out or the changes won't take.

With that said I never have been able to get this to work well. I have better luck setting a static route in the WG1608 to the down stream router ...